How many square feet does 1 gallon of Thompson's Water Seal cover?

Author: Virgie Hamill  |  Last update: Friday, September 29, 2023

Covers 330 sq. ft. (concrete and brick), 150 sq. ft.

How much area does Thompson's Water Seal cover?

COVERAGE Thompson's Water Seal will cover approximately 4 m² per litre. Coverage will vary depending on the texture and porosity of the surface to being treated. DRYING TIME Thompson's Water Seal should be dry in 2 hours under normal conditions.

How many square feet does 5 gallons of Thompson Water Seal cover?

150-350 Sq. Ft. per Gal. Thompsons Waterseal Clear Wood Sealer provides long-lasting exterior wood protection.

Do you need 2 coats of Thompson's Water Seal?

One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. Be sure to read the back label to understand how to properly clean your tools after application. Let the deck dry for at least 24 hours and you're ready to replace the furniture.

Is it better to spray or roll on Thompson Water Seal?

Answer: The manufacturer of Thompson Water Seal recommended that you use their product with a plastic sprayer with a brass wand, such as our Chapin Premier sprayer. There are no concerns about it eroding any of the seals inside of it.

How Much Deck Stain do I Need? | Thompson's WaterSeal

How many years does Thompson's Water Seal last?

Water Seal can only be used on bare and uncoated brick, stone or concrete. How long will Water Seal last? If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.

Is Thompson Water Seal worth it?

Thompson's WaterSeal has clearly not been a consumer favorite with deck stains or sealers. Mainly as it does not offer any UV protection and it grays in a few months. The Transparent and Semi-Transparent versions are prone to premature peeling and wearing after about 1 year.

Can you use too much Thompson Water Seal?

Applying excess amount of sealant can prevent the surface from drying quickly. Consider not using too much water seal to ensure the surface can dry completely as fast as possible. Keep the approximate figure you use in check, and keep your coats as thin as possible.

Can you roll on Thompson's Water Seal?

Thompson's water seal protects your deck from both mildew and mold damage. Can you apply a sealant with a roller? Although it is recommended to use a pump-up sprayer, you can also apply this sealant with a roller, a brush, or a paint pad.

How many square feet will a gallon of water seal cover?

That determines how many gallons of stain are required (each gallon covers up to 400 square feet). You can buy it and be on your way. Thanks to its pigment-suspension technology, there's no need to wait for the Waterpoofing Stain to have its turn in the paint shaker.

What is the best wood sealer?

According to them, these are the nine most effective wood sealers:
  • Thompson's Water Seal. ...
  • Rainguard Premium Wood Sealer. ...
  • DEFY Crystal Clear Sealer. ...
  • Anchorseal 2. ...
  • Roxil Wood Protection Cream. ...
  • Eco-Advance Exterior Wood Waterproofer. ...
  • Ready Seal Stain and Sealer for Wood. ...
  • Pure Tung Oil Natural Wood Sealer.

How much area does a gallon of sealer cover?

Penetrating concrete sealers will typically cover anywhere from 100 – 400 square feet per gallon. Two coats are usually recommended so this will cut the coverage amount in half to 50 – 200 square feet per gallon for 2 coats.

How long does it take Thompson Water Seal to dry?

Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity. Allow minimum of 30 days drying time before applying oil based paint over Thompsons® WaterSeal® Clear Wood Sealer.

Does Thompson Water Seal penetrate wood?

The Thompson's WaterSeal clear waterproofer penetrates deep into the wood.

Should I use Thompson Water Seal on pressure treated wood?

However, most of the water-repellent sealers sold at home centers, paint stores and lumber yards are suitable for pressure-treated wood as well as other outdoor woods such as cedar and redwood. The directions for some, such as Thompson's Water Seal, specify pressure-treated wood as a suitable use.

How long to walk on Thompson's Water Seal?

How Long Does It Take It To Fully Dry & Cure After Application. Now that you've applied Thompson's Water Seal, following the instructions above, to your entire surface, you can walk away and let it dry for 24 hours.

What is the best product to protect a wood deck?

  • BEST OVERALL: Seal-Once Marine Premium Wood Sealer.
  • BEST BANG FOR THE BUCK: Rust-Oleum Varathane Ultimate Oil Based Deck Sealer.
  • PRESSURE-TREATED WOOD PICK: Thompson's WaterSeal Transparent Wood Sealer.
  • BEST FOR WATERPROOFING: Thompson's WaterSeal Clear Wood Sealer.
  • BEST WITH UV PROTECTION: Defy Composite Deck Sealer.

Why is my Thompson Water Seal white?

Product will appear milky white during application, but will dry clear. If puddling of product occurs, remove within 15 minutes by redistributing to dry areas or wiping off.

Is it better to stain or water seal a deck?

Stain offers little to no moisture protection, while sealant offers tremendous moisture protection. Conversely, clear sealants offer little to no UV resistance, while the pigment in many stains can act as a UV barrier for the wood.

How often should you seal your deck?

Your deck should be re-sealed every 1-3 years if you want to protect the wood. This will help preserve your deck for years to come and help it to look brand new. The sealant will bring out the natural wood grain and the sealing will make it stand out.

What happens if it rains after applying Thompson's water Seal?

there is no rush as you deck is not going to get wood rot or fall apart with a little rain on it. In fact it will rinse off all the crap you did not sweep off.

Previous article
What is a standard mortise lock?
Next article
What color sink is best?