If you need to know the electrical requirements for your inground pool, here is a list of common pool equipment and the approximate volts and amps required for each: Pool Pump: 240v, 10amps. Salt Water Chlorinator: 240v, approx 5-8 amps. Pool Heat Pump: 240v, 50 amps.
1 HP is 746 watts x 1.5 HP = 1,119 watts. 1,119watts ÷ 120volts= 9.325 amps.
A 2 hp pump won't pull twice as many amps as our 1 hp example motor UST1102, but it will be more, about 25% more, up to 20/10 amps. The EE version of our example motor, the UCT1102 'The Conservationist', uses 11 / 5.5 max load amps, or a reduction of just over 25%.
One of the most significant consumers of energy in homes with swimming pools are pool pumps, which keep pools clean by circulating water through filters. Pool pumps can consume 3,000 to over 5,000 kWh per year.
Since it's an aboveground pool pump it's an uprated model and probably draws in the neighborhood of 10 to 12 amps at 120 volts. Depending on your plumbing it may draw less.
It draws 1.4 amps of current. I found the chart at this link: http://www.intexcorp.com/media/faq/3214.pdf. Hope this helps.
You can figure about 5,000 watts or 5 kilowatts per hour per 100,000 BTU's for a heat pump. For a typical 100,000 BTU heat pump, that's 5 kilowatts per hour. The national average for Electricity runs $. 13 cents per kilowatt hour.
Every pool must turn over at least once a day, so most pool pumps should run approximately 8 hours a day. But here's the thing: you don't have to run your pool pump consecutively. You can choose to run it for three hours in the morning before you leave for work and another 5 hours in the evening.
It's best to run your pool pump during the day
Not only does sunlight give fuel for algae to grow, it also destroys your pool chlorine and this is why you should always run your pool during the day!
Outside of the air conditioner, the pool pump is the largest electricity consumer in the average pool-containing home. According to the study, at the national average of 11.8 cents per KWh, a pool pump alone can add as much as $300 a year to an electric bill.
Since it's an aboveground pool pump it's an uprated model and draws in the vicinity of 10 to 12 Amps at 120 volts. It might draw less depending on your plumbing.
Pool heat pumps come with union attachments, so you can easily disconnect it and drain the heat pump for winter. Heat pumps require a dedicated circuit with a fairly large circuit breaker. Depending on the heat pump size, it will need a 30 to 50 amp breaker.
A typical above ground pool pump will require a 20-amp breaker and use #12 gauge wire to deliver the electricity.
Booster pumps for pool cleaners or solar systems can be operated with 110V or 220V, and are usually connected to a separate timeclock, powered with a dedicated 15 or 20 amp breaker. The wiring of the motor is identical to the wiring for the main pool pump.
Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Shock is liquid or granular chlorine. You should add one gallon (or one pound) of shock per 10,000 gallons of pool water every week to two weeks. During hot weather or frequent use, you may need to shock more frequently.
The best time to run your pool pump is during the warmest hour of the day; however, keep in mind that this means you will have higher energy consumption, which may lead to an increase in your electric bill. If you want to save on your energy costs, you can run your pool pump at night to avoid peak hours.
So, how much electricity does a pool heat pump use? About 5 kilowatts per hour per 100,000 BTU heat pump. For a general 100,000 BTU pool heat pump, the power you`ll utilize is approximately 5,000 Watts per hour. Typically, the National average for power stands at 13 cents for every kilowatt-hour.
Cost of Running a Propane vs.
The size of your pool also matters, with larger pools costing more to heat than smaller ones. On average, however, a gas heater costs around $200 to $400 a month to run. Electric heat pumps cost less, coming in at about $100 to $200 a month.
A 100,000 BTU heater uses 1 therm of natural gas per hour, so a 400,000 heater consumes 4 therms an hour. 4 therms an hour x $1.67 = $6.68 per hour. So the magic number based on the most common 400,000 BTU pool/ spa heater is $6.68 per hour in gas cost to run your heater.
Re: Amp draw on a 3/4HP pump
Running amps will be 6 to 8 amps.
A 5 HP motor at 230V, 3PH is12.
Using the formula above, multiply 12.4 amps by 10% for a result of 1.24. Add this total to 12.4 for a total of 13.64 amps. The same calculations would apply for a single phase motor.