A well-maintained salt chlorine generator will last 3-7 years. Replacing the salt cell costs $700-$1100. Replacing the control board costs $500-$900. You can extend the lifespans by maintaining a consistent salt level, cleaning the cell only when needed, and using the reverse polarity function.
The control board sends an electrical charge to the cell, and electrolysis occurs, which produces chlorine. Eventually the metallic coating on the cells erodes, requiring the cell to be replaced. A well maintained cell will last 3–7 years at an average replacement cost of $700–$1100.
The easiest way to ascertain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights. Ensure there is enough salt in the pool. On the chlorinator box there should be a light or dial that indicates it is working.
The answer really depends on the use conditions and how often you do maintenance on your pool. The safe answer is that they usually last for about five to seven years. Salt Cells cost between $200 and $900 to replace, depending on your chlorinator model.
Check power
The first step is to confirm that power is reaching the salt chlorinator control box. Make sure that the system is plugged into a GFI outlet, and the test button is not popped or tripped. The control panel has lights that indicate that the power is reaching the system.
Most chlorinators can be repaired but some items or types of damage are simply too expensive or unavailable, in these cases a replacement option will be recommended.
Dichlor is perhaps the most “best of all worlds” chlorine sanitizer. It is typically found in concentrations of 60-65%, which is comparable to cal-hypo. It is a powder sanitizer, which makes it easier to spread or broadcast around the pool than chlorine tablets.
A Salt Water Chlorinator usually costs anywhere from $800 - $1500 for a decent model, which will also rely on the size of your pool.
New salt cells cost anything from $400 and as much as $900 depending on the brand. New cells are anything but cheap, so you'll want to keep yours working for as long as you can manage.
It is best practice to remove your salt cell during the colder winter months. By removing your cell, you limit the potential damage that may occur to the unit during cold or freezing temperatures. The cold water and temperatures can damage the plates and stop the salt cell from functioning as intended.
Chlorine generators need salt to produce chlorine and can't do so if the amount of salt in the water is too low. The desired salinity level in a saltwater pool is between 2,500 and 3,500 ppm. Get a salt-testing kit from a pool supplier and check to make sure that the levels are within this range.
Highly excessive salinity levels (over 6,000 ppm) will cause corrosion damage to metallic equipment, such as ladders and handrails. This is true because salt doesn't wear out, break down or evaporate; Turn the pump on and run until you reach the desired water level.
At the very least, your saltwater chlorinator should be cleaned twice a year, but you should inspect it every two months just to be sure. If it needs to be cleaned, clean it. If it doesn't, then just give it a good rinse with a garden hose.
How much salt does the system require? Salt Systems work best with approximately 3200 parts per million (ppm) of salt, which is roughly the equivalent to a teaspoon of salt per gallon.
Pros of Saltwater Pools
There's less chlorine and less of the heavy chemical scent and content. They're gentler on the skin, with less irritation to the eyes, hair and swimsuits. The water has a softer, silkier feel to it compared to chlorine water. They have lower maintenance costs than chlorine pools.
We definitely think a chlorinator is a worthwhile investment: It automatically and evenly dispenses chlorine (even when you're out of town) You can control the rate that chlorine flows into your pool. You can avoid chlorine tablets in your pool or skimmer (and the vinyl liner stains they can cause.
Automatic chlorinators will work with pools of varying volumes, depending on the chlorinator and your configuration. For example, some automatic pool chlorinators will sanitize pools of up to 40,000 gallons (a pool that holds 40,000 gallons may be about 12ft.
Chlorine gas; disadvantages:
Chlorine is an extremely volatile and hazardous chemical and requires specific precautions for it to be shipped, stored, and used safely. Systems using chlorine gas also have the disadvantage of producing toxic disinfection by-products.
Shock is liquid or granular chlorine. You should add one gallon (or one pound) of shock per 10,000 gallons of pool water every week to two weeks. During hot weather or frequent use, you may need to shock more frequently.
Floating pool dispensers can be used in aboveground and inground pools, but make sure your pool manufacturer says it's safe to use one. The chlorine floater must be removed from the water when people are in the pool.
Are chlorine and shock the same thing? SKIMMER NOTES: No. Chlorine and shock are not the same thing. Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool.
Generally, a salt cell lasts for about 10,000 hours, which is usually around five years for most home pool owners.
The main culprits for leaks are the unions not sitting properly (cross-threading) and old or dirty o-rings in the lid of the cell unit or in the unions. Sometimes cracks in the body of the salt cell or pipes occur. You can fix by tightening unions, replacing o-rings or repairing the crack.