It's not a good idea to use pool shock at the same time as clarifier. Some clarifiers are polymer based and the shock can act to break up the polymer causing the clarifier to be ineffective. It's best to shock your pool before and wait a day or two before adding clarifier.
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals.
It Should Not Be Done Together
Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
When should Pool Clarifiers be Used? Pool Clarifiers are not meant to be used all season long, but are quite helpful at pool opening, after an algae bloom, or battles with cloudy pool water. Follow label directions, but most pools can be retreated after 5-7 days, with a lower dosage than initially used.
If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock. In this case, you should take another reading of free chlorine and do the shocking again using liquid chlorine (sodium hypochlorite).
Clarifier works to clear mild cloudy pool water. Add it every other day as your filter runs until your water clears. If you have extremely cloudy water, you need to use a pool flocculant.
A clarifier requires less work and less water but can take to two to three days to achieve the results you are looking for.
Yes perfectly normal, as the high chlorine shock level lowers so will the pH and it will return to almost where you were before shocking.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.
Algae will remain in your pool after shock if you've had insufficient chlorine and an overabundance of metal elements in the pool water. Therefore, to start the cleaning process. Remove all the debris from the pool with a leaf net and then let the smaller dirt fragments settle.
There are three main causes for cloudy pool water, including poor filtration, chemical imbalances, or environmental factors, like nearby construction, trees, or wildlife. Filter and pump problems can be caused by a range of different issues.
Always run the pump when shocking the pool and allow it to circulate for 24 hours. The water should then be a blue or cloudy blue color. Test the water 24 hours after shocking and start adjusting pH and alkalinity levels. The chlorine will still be elevated, but over a few days, it should stabilize.
The PH rise is temporary, and as the chlorine is used up the ph will drop back to normal. Disregard high PH readings. We recommend shocking with liquid chlorine - granular products add additional things that you may not want in your pool.
Never add chemicals at the same time, whether you're balancing the water, shocking the pool, or adding a specialty chemical. For most water balance changes, the pump needs to run on the high setting for at least four hours before you can add another chemical or retest the water.
To maintain a clear sparkling pool add 4 fluid ounces of Water Clarifier per 10,000 gallons of water weekly. If the pool is cloudy due to dust or to high hardness of the water, add 32 fluid ounces of Water Clarifier per 10,000 gallons of pool water.
Some of the best natural homemade pool clarifiers include baking soda solution, bleach, white vinegar, lemon juice, rubbing alcohol and borax. Compared to commercial chemical clarifiers natural ones have enzymes that break down the dirt in the water making it easy and cheap to filter them out.
Wait until the chlorine level in the water drops down to 1-4 parts per million (ppm) before allowing swimmers back into the pool. If the water still looks a little cloudy after the shock treatment, you may want to use a water clarifier before allowing swimmers back into the pool.
Vacuuming After Shock
Shock the pool with either the liquid or granulated chlorine shocks. Let the filter run for 24 hours before adding any other chemicals. You should see a noticeable difference the next day in the water clarity.
So if you buy liquid shock, be aware that it only lasts one to two months at the most before it starts to lose effectiveness. While many swimming pool chemicals stay good for years if stored correctly, some pool-maintenance supplies expire more quickly.
The fastest way to clean a green pool is by using pool chemicals and your pool filter. This process usually takes around 4-5 days but you will start noticing a major improvement after 24 hours.
Use a pool brush to vigorously scrub any pool surfaces covered in algae, including the walls, floors, and steps. Apply a green algaecide according to the directions on the label. Let the water circulate for 24 hours, then brush the pool surfaces again. Vacuum or backwash to remove any remaining dead algae.