If you can't unclog the toilet using a plunger or a snake, your next best option is to use boiling water. Boiling water can help to dissolve the clog and free up the pipes. To use this method, bring a pot of water to a boil and pour it into the toilet. Let it sit for a few minutes, and then flush the toilet.
If a plunger or plumbing snake doesn't work, water and soap might do the trick. Boil a gallon of water and allow it to cool for about 10 minutes. As you wait, pour a cup of liquid dish soap into the toilet bowl. You can then pour the water slowly into the bowl — leave it for about 20 minutes before flushing.
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.
Vinegar and Baking Soda Mixture
To start, completely dissolve one cup of baking soda in one cup of hot water. Pour the mixture into your blocked toilet and wait a couple of minutes. Then, pour two cups of vinegar into the toilet. Allow the vinegar and baking soda to react for at least 15 minutes.
Baking Soda & Vinegar
The combination of baking soda and vinegar is an excellent way to dissolve clogs. For toilet clogs especially, add one cup of baking soda to the bowl and let it sit for a few minutes. After that, slowly pour in two cups of vinegar. Let the mixture sit again for an hour, then flush down the toilet.
When a toilet has a clog made of water-soluble materials, it has a chance of slowly dissolving in the water and freeing up the toilet to work properly again. So, clogs that are primarily made of toilet paper can clear themselves.
Ideally, no more than five or 10 minutes. One plumber told us that if plunging goes on any longer, it's time to try a toilet snake or call an expert.
Toilets may not flush for various reasons, including a disconnected chain, faulty flapper, low water level, a damaged float, rim jet clogs, or simply a drain blockage that needs to be cleared with a plunger.
Is it okay to leave a clogged toilet overnight? In most cases, you can leave a clogged toilet overnight. However, calling an emergency plumber near you might be warranted if water starts leaking from the pipes. A simple clog likely won't cause this, but an inexperienced homeowner messing with the plumbing could.
Plumbing Auger
To clear a toilet clog, the auger is inserted into toilet and twisted by hand, or by machine, to help break up the obstruction. Typically, an auger or drain snake would be used if a plunger is not resolving the clog.
A manual drain snake, also known as a plumber's snake or a drain auger, is a small boring tool that rotates slowly as it's physically pushed through a stubborn clog. The terminal end of the device is a corkscrew-shaped hook that is fed into a clogged drain or toilet.
Many people think that a forceful push into the plunger is what frees up the clog, but this can often worsen the problem. In fact, pushing the plunger in with enough force can even break the seal of the toilet gasket (the seal between the toilet and the floor where the plumbing exits).
Aside from vinegar and baking soda mixture, applying bleach is one of the easiest and cheapest methods for unclogging a blocked toilet.
Maintain a seal and plunge up and down rapidly, keeping the plunger under the water level and lifting it only an inch or so on every upstroke. Be patient, as it may take multiple plunge cycles, of a dozen plunges per cycle, to loosen the clog. Flush to see if the clog has cleared. If not, repeat.
Once you force out the air, plunge vigorously in and out, maintaining the seal. You'll be forcing water in both directions in the drain, which will effectively loosen most clogs. Stick with it, plunging 15 to 20 times if necessary.
Start slow and add force as needed. Several gentle pumps will usually work better than a couple of hard pushes. If your blockage is going to come out, it should happen in less than 10 minutes.
Warm Up Your Plunger
Stiff, hard plungers don't work as well as soft and pliant ones. Run your plunger under some hot water before you use it. This will soften up the rubber, which will help you get a better seal on the toilet bowl.