How Much Water Pressure Should a House Have? Most often homeowners complain about low pressure; however, having high pressure can result in expensive damage. The pressure level can vary, but 60 PSI (pounds per square inch) is recommended for most residential homes. Water pressure should not be higher than 80 PSI.
Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that's between 60 and 70.
Residential water pressure tends to range between 45 and 80 psi (pounds per square inch). Anything below 40 psi is considered low and anything below 30 psi is considered too low; the minimum pressure required by most codes is 20 psi. Pressures above 80 psi are too high.
According to statistics, water pressure above 80 psi (pounds per square inch) causes the failure of water fixtures. The most common signs are spitting or leaking faucets, especially if it's out of the cold tap.
Consider calling a professional if the water pressure reading goes above 80 psi.
If the pressure of the water entering your house is 100 psi or above, it can damage the plumbing.
Normal water pressure range
In general, residential water pressure ranges between 45-80 psi (pounds per square inch). If your water pressure is under 40 psi, it's considered low. A psi between 20-30 is considered very low, and under the minimum water pressure required by most building codes.
A quick and easy way to increase water pressure is to adjust the pressure-reducing valve, which can be found in your home, usually close to your water meter.
One of the main giveaways of high house water pressure is noise. Banging sounds coming from the pipes usually indicate a problem with pressure, and these noises tend to be very noticeable when the water pressure is too high.
Most residential plumbing systems are designed to handle 40 to 60 PSI of pressure, with 80 PSI being the typical maximum and anything over 100 PSI being possibly detrimental to plumbing components.
The ideal water pressure for a house will be somewhere in the range of about 45 to 65 psi. Anything higher than 80 psi can cause damage, and anything much lower than 45 psi may result in issues when you use your shower, toilet, dishwasher and other water-consuming appliances.
Disadvantages of whole house water filtration systems:
May decrease water pressure: The water supply runs through the filter at a certain speed. If you are taking a shower, doing laundry, and running your dishwasher at the same time, you may notice a decrease in water pressure.
Find the spigot closest to your source of water. Make sure all the taps and other water uses are turned off in your house. Now turn on the spigot and see how long it takes to fill the bucket. Dividing the number 60 by the time to fill the bucket will give you the gallons per minute number.
A water pressure regulator, if you have one, is usually located where the main water line comes into the house and after the main shut off valve. This way if you need to work on or change the water pressure regulator you can simply shut off the water main to do so.
If you wish to reduce the water pressure to a particular faucet, turn the valves clockwise by a quarter rotation. Make sure to turn the cold and hot water valves equally to create more consistent water pressure.
Open your main water valve.
Find the valve and check to see if it's completely open. Opening a half-shut valve is one of the quickest ways for increasing home water pressure. Sometimes the main valve is turned off accidentally during routine repairs and maintenance without the homeowner's knowledge.
The typical residential water flow rate for small households is between 6-12 gallons per minute, so unless you plan to add extra kitchens, bathrooms, or laundry rooms to your home in the future, your home will never need to exceed that final GPM, assuming your flow rate is already normal.
The short answer is low water pressure in your home arises due to a number of causes. Some include a shut or blocked water meter valve, mineral buildup clogs pipes, corroded pipes, or even a crack in the main city supply pipe to your home.
Many toilets really do leak only at night; that's because people use much less water during these hours and in many municipal water systems, the water pressure rises considerably during this time.
Water pressure regulator replacement: $250 to $1,000. Pipe section replacement: $500 to $4,000.
High Pressure
Excessive water pressure can cause stress on your plumbing leading to leaks and burst pipes. If you hear banging from your pipes (known as a water hammer) this is a sure sign of high water pressure. It may mean that the water pressure from your supplier to your house is too high.
Shower Heads - The optimal water pressure for a shower head is between 40-60 PSI. Below 40 PSI the flow of water may be weak and unsatisfying, while over 60 PSI it may be uncomfortable or even painful.