Borax and vinegar are both effective and natural cleaners. They can effectively eliminate mold in your home without the use of toxic chemicals. While borax can be toxic if ingested, it is safe to use around your home not only as a cleaner, but as a deodorizer, insecticide and herbicide.
For very soiled walls, mix at least 2 tbsp. borax, 1/2 cup vinegar and 2 cups warm water. Spray the walls and wait five minutes before wiping them down. Trisodium phosphate, or TSP, is another cleaning material often used to remove grease and smoke from walls prior to painting.
Usually a half of cup of borax to one quart of water should do the trick. You may also try mixing borax, vinegar, and water for stubborn mold infested areas. The ratio for this is typically a half cup of vinegar, one quarter cup borax, mixed with 1 quart of water.
Luckily, both Borax and vinegar are completely safe cleaning products! By using Borax cleaning powder diluted with vinegar and warm water, you're able to effectively remove any mold problems. Moreover, you can also use Borax as an ecological insecticide, herbicide, and even deodorizer!
If it has not been cleaned for a long time and is smelling bad, then empty around a cup of borax in it. Let the borax do its work by leaving it in for at least 15-20 minutes. Rinse and leave to dry. You can sprinkle some borax in the can before using it again, to minimize odor when in use.
Borax is a gentle but effective alternative that raises the pH of your detergent enough to kill bacteria without being corrosive enough to damage the paint.
If the mold is still hanging on, it's time to bring out the borax, which is an alkaline mineral salt cleaner that's safer to use than bleach. Combine a tablespoon of borax with a cup of water, then apply this solution to the mold with a soft-bristled brush. Scrub away the mold, leaving the borax solution in the wood.
Scrub the surface mold stains from walls and wood trim with a mixture of one quart water and 1/2-cup bleach mold cleaner to kill the mold. Use a soft brush and work until signs of the mold disappear. After scrubbing the surfaces, allow the bleach solution to continue to penetrate the surfaces and dry.
Mix 1 cup borax with 1 gallon of warm water. Pour some of the solution into a spray bottle. Spray directly onto the surface you want to clean. Use a scrub brush, sponge, or clean rag to remove mold stains.
Go with the safer option. Not only is OxiClean the safer option, but it comes in several forms, including powder, liquid spray, and laundry detergent; borax is only sold as a powder. Learn more about the many ways you can use OxiClean on Amazon or OxiClean.com.
Mix one teaspoon of baking soda along with two cups of water and shake in a spray bottle. When thoroughly dissolved spray the solution onto the mold and scrub with a brush. Repeat if necessary.
Hydrogen peroxide may be one of the most effective mould-killing solutions. It is anti-viral, anti-fungal and anti-bacterial. You can clean mould from your ceiling, walls and floors using hydrogen peroxide. Just keep in mind that hydrogen peroxide acts like bleach and affects delicate surfaces.
Nontoxic household cleaners are a great way to keep your home green and clean. Borax and vinegar are two safe ingredients that can be combined to create a good general cleaning solution. Undiluted vinegar and borax can also be used for mildew removal.
borax. 20 Mule Team is the best known brand of borax, which they sell primarily as a laundry detergent booster.
Use 1 part bleach to 3 parts water, according to Sherwin-Williams. If you don't want to use bleach but do want something other than water, try vinegar, borax or branded products that you can find at a hardware store or home center, which also kill mold.
Use undiluted white vinegar on hard surfaces in kitchens and baths. A bleach solution also works to kill mold. Mix one cup of bleach in a gallon of water, apply to the surface and don't rinse. Mix a 50/50 solution of ammonia and water.
Mold professionals use expensive, professional equipment such as HEPA (High Efficiency Particulate Air) air scrubbers, HEPA vacuums, commercial-strength dehumidifiers, etc. Regular handymen won't have that stuff. Some mold remediation companies also do restoration work, just like a general contractor.