You can protect the joint sand from washing out by sealing the paver surface. Sealing restores the beauty of your pavers. The paver sealer also serves as glue between the joint sand particles hence holding them together, and preventing the sand from being washed away when it rains or during pressure washing.
A danger of using too much water too quick creates the possibility of washing away the polymers. Too little water used in the installation process could leave you with a fragile joint. If the joint is not properly watered to at least 2/3's depth, a hardened crust may form at the top of the joint.
However, you should NEVER install polymeric sand when it is raining! Rain activates the polymers before the sand is in the joints which will ruin your hardscape by producing a haze and adhering sand grains to the surface of the pavers.
Unsealed interlocking pavers & brick are subject to staining, fading, sand loss, and can sometimes develop weeds and mildew growth. With proper sealing and maintenance your pavers will be more likely to have a long lasting, beautiful and durable life and appearance.
Traditionally, concrete paver manufacturers have recommended waiting at least 90 days after polymeric sand installation to apply a protective sealant to a paver surface. Nowadays, a 30 day delay is sufficient to allow the evaporation of any remaining natural efflorescence contained in the pavers.
No, new product won't adhere to the old. You have to remove the old polymeric sand and then apply fresh product for the best result. How to replace polymeric sand between pavers? Inspect the pavers to make sure the sand in the crevices is at least 1/8″ below the top of the pavers.
Prior to the installation of new polymeric sand, you will need to remove any old joint sand or polymeric sand from the joints with a pressure washer. If remov- ing polymeric sand, a hot water pressure washer will help to soften up the binders in the sand.
Regular sand for paving is prone to erosion, damage from weeds and can make your pavers hard to wash without risking the loss of any jointing sand between the stones. Using polymeric sand, however, prevents weeds from taking root and holds pavers firmly in place thanks to the durability of its seal.
Polymeric sand is the most popular and useful filler used under brick pavers. It is a mixture of fine sand, adhesive and is most widely used in paver joints. Typically, polymeric sand lasts for up to 10 years. But if you use high-quality polymeric sand, it can last for approximately 15 years.
Natural sand is a more suitable option than polymeric sand for bedding. Also, it is excellent for people looking for a budget-friendly option.
Sand and soil hardeners, such as NanoPave JSS, or Tamarron's Joint Hardener. are two such chemicals that can be sprayed over the sand before and after troweling it smooth. It bonds with the sand to create a hard surface to prevent dents and also resist roots, termites, rodents, nutgrass and weeds.
If there is a huge downpour, it's best to postpone the process. Sand will surely get wet and wash out of the joints, so it is best to reschedule and start from the beginning. If there is light rain, you'll most likely have nothing to worry about.
If you use regular sand, you may have to re-sand pavers every two years. But, other indicators may mean that the time has come. If joints are open, it means that any sand in there to keep the brick stable, keep them from moving, was washed off.
If your polymeric sand didn't harden up, it's pretty much guaranteed there's a moisture issue. If the joints remain wet after the installation, they will remain soft until they dry. So getting one initial complete drying "set" is very important to the long-term performance and lifespan of the product.
Any excess polymers and sand should be rinsed off of the project surface. Go over your pavers again with a leaf blower to blow any excess water and sand off of the surface of your pavers. Work in small areas to be sure you remove as much standing water and/or sand as possible.
To maintain polymeric sand joints, keep a bag of this high-grade sand at hand so that you can use it whenever the need arises. You need to keep the package away from sunlight in a dry place. Do not take the sand out of its package unless you are applying it.
Best appearance is achieved by eliminating all polymeric jointing sand from surfaces. A minimum of 24 hours drying time is required prior to allowing foot traffic and 48 hours for vehicular traffic on the paver surface.
The first day, a chemical wash is done followed by pressure cleaning with a 5,000 P.S.I pressure cleaner, getting almost anything out(stubborn penetrating stains like oil and rust may not come out). The second day, given that the surface to be sealed is completely dry, a sealer is sprayed on the pavers.
If your surface has a slope, start at the lower end and work your way up. Concentrate on small areas at a time (a good rule of thumb is 200 s.f. increments). Generally speaking, you'll want to perform three rounds of watering. The initial showering should be done at a height of about 4 ft.
Regular sand can wash away after a heavy rainstorm. But this isn't an issue with polymeric sand, which reduces the amount of water that will work its way into the space between your pavers.