Blend ¼ cup quantity of liquid dish detergent in vinegar. Shake the spray bottle to blend both ingredients. Spray the cleaning mixture on soap scum and other dirty regions of bathtub. Wait for 10-15 minutes and then wipe the treated areas with a soft sponge.
Mix ½ cup bleach into about a gallon of water. Using a sponge, coat the tub's surface with the bleach and water solution and wait 5 minutes. After 5 minutes, scrub the surface with the sponge, paying special attention to the tougher stains. Rinse the tub with cold water, being careful not to splash the bleach.
Make a bathtub cleaner paste of one part hydrogen peroxide to two parts baking soda (or cream of tartar). Rub the paste on the stain and let stand for 30 minutes to one hour, then wipe and rinse. If necessary, repeat until the stain is gone.
First, cover the stained area with a coat of baking soda. Then, mix up your cleaning solution in a spray bottle: 1 cup vinegar, 1 tablespoon of dish soap, and 3 cups of water. Spray this mixture over the baking soda. Use a soft sponge to scrub the stained areas.
Soap scum and grime can clog your drain and prevent easy drainage, which will then contribute to grime buildup around the edges of your tub where the water rises while you're showering. Prevent clogged drains and avoid pipe problems with our help!
Back to the question, “can bleach damage a bathtub?” Yes, it can. Bleach can add stains to your bathtub is misused. Remember, it is a massive chemical that, if not used correctly, can cause more harm than good.
Scrub it with a stiff cleaning brush and then follow up with a melamine sponge like Mr. Clean Magic Eraser. If that doesn't work, you may need to use some CLR cleaner or Purple Power concentrate. With both of these, I'd add quite a bit and fill the tub with hot water and let soak for a good 30 minutes before scrubbing.
Diluted bleach is particularly effective at combating mold and mildew growth in your tub. If you have dirty tiles around the tub, ordinary hydrogen peroxide is an effective tile and grout cleaner, and white vinegar is good for cleaning bathtub fixtures. Never use all of these chemicals at once, though.
That's right: Grab your dish soap and a broom, and you might be as pleasantly surprised as we were to learn that Dawn is apparently just as effective at banishing bathtub scum as it is at removing all that grime and grease from your dishes and pans. Plus, this technique is equal parts simple and fast!
A. Household bleach is an alkaline material and consequently will precipitate iron out of water. It sounds like that's what happened since iron stains are rust colored. A mildly acidic household product made for removal of iron stains should take care of it.
Heat one-fourth cup vinegar and pour into a spray bottle. Add one-quarter cup liquid dish detergent, and it give a little shake to distribute. That's it! The vinegar and dish soap work together to tackle soap scum and dirty tub rings.
Like magic, the Magic Eraser will start powering through tough grime in just a few swipes. Before you know it, your clean bathtub with shine like the top of Mr. Clean's head! And remember, you can also use Magic Eraser to clean other surfaces too.
Pour a generous amount of dish soap into your tub and then start scrubbing with the broom. The stiff plastic bristles will deliver a deep clean, even against tough stains. When you're done, rinse the tub and you're all set.
Clever solutions for a spotless tub. Get the gunk off old enameled bathtubs and sinks by applying a paste of 2 parts baking soda and 1 part hydrogen peroxide. Let the paste set for about half an hour. Then give it a good scrubbing and rinse well; the paste will also sweeten your drain as it washes down.
White vinegar
If you have a fiberglass tub in your bathroom, it may appear dirty and dingy. However, a simple mixture of two parts white vinegar and two part water is all that's needed to remove the discoloration. Mix them in equal volume and pour the mixture into the bathtub.
Pour equal parts of vinegar and Dawn into a spray bottle. Gently shake, then spray liberally onto the surface to be cleaned. I have found the best results is when I use it to clean chrome shower and sink fixtures. After spraying on the fixture, rub and wipe it with a microfiber cloth to avoid scratching.
12 ounces of Dawn dishwashing soap, 12 ounces of hot white vinegar (heat in the microwave). Dump them in a spray bottle (99 cents at walmart) and shake it gently to mix. Spray like crazy on those tiles. It works great at taking off soap scum and just general cleaning for the bathtub area.
Baking Soda
This method is important because you don't want to accidentally mix bleach with another product as you try to fix the white spot! Baking soda, sodium thiosulfate, and hydrogen peroxide all work in different ways to neutralize the bleach.
Leave the room and give the bleach a chance to disinfect, kill mold and mildew spores and lighten stains. You should let the bleach solution stay on the bathtub surfaces for at least 10 to 15 minutes.
But the peroxide is cheaper and more ubiquitous.) Why the tub turned red: The bathtub is an old porcelain with a ferrous (iron) component. The chlorine element in a classic chlorine-based bleach oxidizes the iron from the porcelain. Oxidized iron is rust, hence the rusty red color.