Algaecide will kill the algae and mold affecting your pool water, but it is best used as an algae preventative. While it does not change the pH balance of your pool water, it will keep algae from growing and work with your chlorine sanitizer to keep those levels balanced.
Add a preventative dose of an algaecide to your pool every week after shocking. Algaecides not only kill algae—they can prevent its growth as well.
Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
You can get rid of algae quickly by vacuuming and brushing your pool, balancing your pool's water chemistry, and then shocking and filtering your pool water. Just be thorough as you clean your pool surfaces. If you leave behind even a small number of algae spores, it won't be long before they regrow and bloom again.
Let the water circulate for at least two hours.
Circulate the water for about 2 hours to ensure the flocculant is fully mixed in, then shut off your pump and let it sit overnight. During this time, the chemical will start to bind the particles together and settle them to the bottom of the pool.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
GETTING RID OF ALGAE
Liquid Algaecide is a strong algae depressant used for the prevention of algae growth and the maintenance of sparkling water in pools. Algae growth is the main cause of “off” colours in your swimming pool water.
Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.
Use the biguanide algaecide for your pool, measuring 16 ounces for every 10,000 gallons of water.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
There are a few different types of algaecides that contain various chemicals to suppress and fight off algae. Many of them include copper or copper sulfate. It's this copper that oxidizes in the water. And when copper oxidizes it turns a green color causing your pool to look green.
Algaecides treat and prevent pool algae, but not all algaecides are created equal. To treat green pool water, ensure you select an algaecide that kills green pool algae. After treatment, some dead algae may remain in your pool. Continue to thoroughly brush your pool's surfaces often.
If algae grow on the leaves and stems of your aquarium plants, create a routine of cleaning them regularly. Using a solution of 5-10% bleach, dip the plants for a few minutes as needed to destroy the algae. Make sure they are thoroughly rinsed because bleach can kill your fish. Invest in a filter.
Pool algae can be caused by poor filtration, out-of-balance water, low or inconsistent chlorine levels, or poor water circulation. Green, dark green, yellowish green and blue-green algae are the most common. Green algae are slimy.
A nylon or rubber brush is the correct choice for scrubbing the sides of a soft-sided above-ground pool. A large pool brush makes quick work of the job, but you may need a smaller brush to clean corners. Once the particles have been removed from the sides of the pool, turn your filter back on and agitate the water.
If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy. If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock.
Winter Pool Algaecide is highly effective at preventing all forms of algae. Polymer pool algaecide stays strong all winter providing dependable control of algae growth throughout the winter season. Unique winterizing algaecide is specifically formulated to fight cold weather algae for up to 5 months in a covered pool.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
The HTH Ultimate Algae Guard is the one that is added every 90 days, it is a copper based algaecide.
Chlorine—yep, your typical sanitizer—is much more effective at killing algae than algaecide is. Even if your water gets cloudy and your walls get slimy, chlorine can still kill it. That's because chlorine oxidizes bacteria and single-celled algae, which means they trade electrons.
It took two days but it was completely gone. Not a trace. I would so recommend this product.
Registered algaecides include copper sulfate, copper chelates (ethanolamines, ethylene diamines, triethanolamines, triethanolamine + ethylene diamine, and copper citrate/gluconate), endothall (as the mono (N,N-dimethylalkylamine) salt), and formulations containing the active ingredient sodium carbonate peroxyhydrate.
pH Balance and Chlorine
Algaecides do not directly affect the pH balance in your pool, but too much algae will raise the pH level. By eliminating algae, the algaecide helps return pH levels to normal.
To kill green algae, add a chlorine-based shock to the pool. Give the pool a thorough brushing and run your filter to remove the dead algae from the water. After you've killed the algae, you'll need to add a clarifying product (flocculant) that will cause the skeletal remains to sink to the bottom.