Remove the skimmer basket and push the end of hose into the suction hole. 4. Close any other skimmer valve and adjust main drain valve for proper speed. 5.
Now, here answers the question earlier: do you leave skimmer basket in when vacuuming pool? YES, you need to remove the skimmer or strainer basket before attaching the open end of the hose to the inlet. Finally, plug the open vacuum hose into the suction port.
I check the pump basket two or three times a week, but it usually only needs emptying every couple of weeks.
Yes, we recommend backwashing after you vacuum your pool. This allows the filter to shoot out any dirt / debris you have vacuumed up. Don't forget to set your filter to “rinse” for 30 seconds after backwashing!
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
For routine vacuuming, the filter valve is left in the normal “Filter” position. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. The "Filter" setting is used for light to moderate levels of pool sediment.
Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.
After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear. Shut off the pump motor and push the T-handle back down into locked position. Turn your pump back on and note the lower pressure.
Backwashing reverses the flow of water, lifts up and flushes the sand, and then expels the dirty water via a waste line into the ground or drain. In order to prevent residual blow back into the pool, once you've finished backwashing it's highly advisable to rinse the filter.
A commonly asked question amongst our customers is, “when should we clean our pool's filter cartridge?” Typically, we recommend that your cartridges inside your filter be cleaned every 3 months for longevity of your cartridges, as well as for better pool filtration and water flow.
If you do have this option, it is highly recommended that whenever you have algae, you will need to vacuum to waste. This option allows you to vacuum the algae up and send it out through the backwash line, avoiding getting algae into your filter sand.
Without a plate, you will need to remove the skimmer basket and attach the hose directly to the inlet. And since the basket is out of the way, unstrained water will be vacuumed into the skimmer inlet which can cause it to clog and even damage the filter if large debris reaches it.
When you first install a sand filter or renew the sand, you may indeed get a small amount of sand coming out when backwashing, rinsing or filtering. Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs.
* Can i discharge the backwash water onto my lawn, will it harm the grass / plants? The DE doesn't harm the grass or plants, excessive chlorine or saltwater may.
Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
In a sand filter, the rinse cycle allows water to flow back down through the sand to flush out any remaining dirt and debris from the filter and piping. The rinse cycle also restratifies (deposits in layers) the sand, letting it resettle in the filter tank.
If dirt is reappearing at the bottom of your swimming pool after you've vacuumed it your pool's filter may be working poorly. Pool filters often work poorly because they're in need of cleaning. If you have a sand filter for your pool you need to make sure that the sand is sharp and freshened up.
During backwashing, the water flows in reverse, from bottom to top, out of the laterals and up thru the sand, to flush out the trapped dirt from the sand bed, and send it out the waste line. Sand filters can have either a push-pull valve (also known as a slide valve) or a multiport valve.
if dirt is escaping back into the pool, it could be because the filter is dirty and clogged, which means it needs to be backwashed. When the pressure gauge rises eight to ten pounds per square inch (PSI) above it respective normal operating range, backwashing is necessary.