No - it comes with wires to the dishwasher in a box on the front. If your existing dishwasher uses a standard plug under the sink, you would need a power cord. If your existing dishwasher taps into a romex cable in the cabinet you can just use a couple wire nuts to hook it up in the power box.
Dishwashers can be either hardwired, or cord-and-plug connected. Check the owners manual of the unit you have, but in most cases the decision is left to the installer. In newer homes you'll commonly find a 125V NEMA 5-15R receptacle supplied by a 20 ampere circuit, used to supply a dishwasher and disposer.
Unlike plug-in appliances, a dishwasher must be hardwired and hooked up to the home's plumbing. If you're for the challenge of installing it yourself, you can save a lot of money.
Dishwashers are hardwired. They consume a relatively high amount of power, so it is not advised to use the same method to connect your other household appliances.
Each dishwasher comes with a junction box (with power cord) to be installed in a cabinet next to the dishwasher cutout. It can be installed by an installer, servicer, technician, electrician or other qualified professional and is intended for hard-wired installations.
No, not all dishwashers are hardwired. Instead, you can purchase dishwashers that come prepared with an electrical cord and a three-prong plug. These units will easily connect to a regular wall socket that you'd have in your household kitchen.
A: This is needed for a hard wired installation as the cord that comes with the dishwasher is only for plugging into a three prong outlet. The plug side of this is for connecting to the back of the dishwasher and the junction box at the end of it is for a hard wired connection.
In the time it takes to run to the breaker box to turn off the breaker, the dishwasher could deposit an inch or two of water on the floor. A hard-wired connection, on the other hand, avoids the need for an extra receptacle under the sink, where there may not be room for one.
To hardwire a dishwasher means to connect the machine directly to the circuit wire that leads to the home's electrical panel, rather than simply plugging the dishwasher cord into an electrical outlet.
The receptacle should not be behind the dishwasher. To access it; you would have to remove the dishwasher. Just like the dishwasher drain and water line that go to the sink water valve and drain; the dishwasher electric cord plug should go to a receptacle under the kitchen sink.
According to the electrical code, the dishwasher should be on its own circuit. The dedicated dishwasher circuit can't supply any other appliances, lights, fixtures, or outlets. In addition, the circuit that is servicing the dishwasher also needs to have a circuit breaker with at least 15-amps.
All Bosch dishwashers come with 110v power cord for plugging into wall outlet. If you are hardwiring then you must use the Bosch power cord with junction box accessory.
Kitchen dishwashers installed in dwelling units require GFCI protection whether hard wired or cord and plug connected. Code Change Summary: A new subsection was added regarding dwelling unit kitchen dishwashers. Now, outlets that supply dwelling unit kitchen dishwashers must have GFCI protection.
Dishwasher Circuit
When installing a dishwasher, the circuit should be a dedicated 120/125-volt, 15-amp circuit. This 15-amp circuit is fed with a 14/2 NM wire with a ground. You may also elect to feed the dishwasher with a 20-amp circuit using 12/2 NM wire with a ground.
With the right tools, hardwired dishwashers can be converted into plug-in dishwashers. This way, you can plug the dishwasher directly into a wall socket without permanently fixing it to the wall's wiring.
Yes, the dishwasher and garbage disposal can run on the same circuit. But they are more preferred to be powered by two different circuits rather than one.
The dishwasher needs a single-pole breaker that has at least 15amps. If you operate the dishwasher on the same circuit breaker as the garbage disposal, you need to use a 20 Amp breaker.
A smart dishwasher needs to be hardwired. Since there is frequently no receptacle under the sink, you cannot utilize the plug-in approach. According to the National Electrical Code, all dishwashers' outlets need to be accessible for the dishwasher to be hardwired.
There are no requirements in National Electrical Code (NEC) that a residential disposal must be GFCI protected.
Newer Bosch dishwashers use a special power cord that plugs into the back of the unit. It comes with a standard 3-prong cord that works if you have an outlet for power. If you have a hardwired dishwasher, this box allows for an easy-to-wire junction box with a white, black and green terminal.
All Bosch dishwashers are compatible. The box cord is used in hard-wired installations. Installation instructions can be found here.
The dishwasher is designed for an electrical supply of 120V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amps.
We all know refrigerators and dishwashers require a power source to operate, but can they be on the same circuit? Yes, a dishwasher and refrigerator can be on the same circuit if you can reach the requirements on the NEC.
Can You Put an Electrical Outlet Under A Sink? The National Electrical Code, a minimum standard for electricians in the United States, allows for electrical outlets to be placed under the sink. However, all electrical outlets within a distance of 6 feet from the sink must have GFCI protection.