Apply as supplied using a brush, roller or sprayer. Do not thin for
I sprayed kilz with the harbor freight LVLP sprayer without diluting it and it worked pretty well.
1. Surface Prep: Clean and sand your surface as needed to ensure it is smooth and ready for primer. 2. Apply Primer: With your chosen tools, apply the primer in even, controlled strokes or rolls, following the specific directions for your Kilz product.
The company says: ``Best results for stain blocking are obtained with no thinning. However, KILZ 2 Latex primer and KILZ Premium primer may be thinned up to 10% per gallon with water.''
There were some water marks from prior leakage and I used the KILZ aerosol spray to cover and prime these marks. It was very easy for this novice to use and did an excellent job of covering the marks. Needless to say she was right. After a 10 minute prep and spray, my stains were gone.
There are basically three types of sprayers: Airless, piston pumps that use high pressure to shoot paint through a tip. This one can lay down a lot of paint quickly and works well with thick latex paints and primers.
Original Kilz Primer allowed more seep through when put in two coats to two different walls in the same area, whereas Zinsser provided superior coverage.
KILZ® can be easily sprayed .
Prepare the primer
If it is on the thick side, you should dilute it to ensure effortless application with your paint sprayer.
KILZ 2 ALL-PURPOSE Primer (Previously KILZ 2 Latex) is a fast-drying, water-based, multi-surface primer-sealer-stainblocker with excellent adhesion, mildew resistance, sealing properties and very mild odor.
Depending on how strong or bold the previous color is, it may be necessary to apply more than one coat of primer. However, it is not necessary to over apply the primer with so many coats. As long as the primer applies uniformly over the previous color, then one or two coats should be sufficient.
Prior to applying the primer, remove any mold or mildew with a proper remover or have it removed by a professional. In severe cases, the moldy substrates may need to be replaced. Once the surface is mold and mildew free, ensure it is clean and dry before applying primer.
Overall, it is viewed as a cost-effective solution for priming and sealing surfaces before painting. Great product!! [This review was collected as part of a promotion.] My project would not have turned out so well without using Kilz.
Primer is the foundation and paint is the color; they are not the same. According to representatives from SATA, one of today's leading spray gun manufacturers, modern primer and paint products are more sophisticated than ever and require more precise mixing and application. One gun will not do everything.
Apply as supplied using a brush, roller or sprayer.
Why don't painters use sprayers? Sprayers require significant prep work to protect non-painted areas from overspray. They also need thorough cleaning post-use. Some painters prefer the simplicity of traditional methods like brushes or rollers.
Conclusion. Typically, back rolling after spraying on walls and ceilings is ideal especially for your primer. It will help in promoting better adhesion of the primer and reduce issues of raised filaments with drywall.
DO NOT THIN if using a roller or brush; however, if using a sprayer and thinning is required, thin with water at a ratio of no more than 8 oz.
The EPA registered active ingredient creates a mold and mildew-resistant film that protects the primer film from mold and mildew growth. KILZ MOLD & MILDEW Primer will block most medium to heavy stains including felt marker, grease, ink, pencil, tannin and water stains.
Dries to the touch in 30 minutes. Can be recoated or topcoated in one hour with latex or oil-based paint. Low temperatures, high humidity or poor ventilation can significantly increase dry and paint application times.
Kilz works to trap and seal odors, block stains, or even fill in porous surfaces. By doing so, it leaves a smooth base for fresh paint to go on smoothly and look its best.
Oil-based primers are the best option for old walls. They have superior stain blocking abilities, and will keep any old stains from bleeding through to new paint. Oil-based primers are also great at sealing out moisture, which can be a major problem for old plaster walls.
Shelf life under normal conditions is two years unopened. Partially used cans might develop skinning if not tightly sealed.