The procedure for adding granular chlorine is pretty much the same as adding calcium chloride or sodium bicarb to a pool. Measure the dry chemical, pre-dissolve in a bucket, and pour around the perimeter of the pool (never into the skimmer directly). There are a few types of dry, granular chlorine.
Adding chlorine to your pool water will kill viruses and bacteria, keeping you, your friends, and your family safer when swimming. Stock up and save money on chlorine tablets for the season by getting the standard 3-inch stabilized chlorine pucks.
Neither will chlorination be effective with a diffuser and without a pump. The best thing to do is to apply liquid chlorine in the pool. Then, you have to circulate the pool manually with the use of a telescopic pole or paddle. This will ensure the chlorine disperse well.
Short answer--yes. The first response, however, would be why would you use a pool without a filter? The sand filter or other filtration system is essential to the health and safety of the swimmers. It is also necessary to have a circulation pump for maximum chlorination.
Shocking a pool with liquid chlorine or a granular pool shock kills or inactivates pathogens and algae. Shocking will also oxidize other unwanted materials inhabiting the pool water.
Shock is liquid or granular chlorine. You should add one gallon (or one pound) of shock per 10,000 gallons of pool water every week to two weeks. During hot weather or frequent use, you may need to shock more frequently.
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool. It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours.
Smaller inflatable pools, like kiddie pools, aren't typically treated with chlorine. These pools are small enough to refill with fresh water fairly easily, so small inflatable pool owners typically don't have to deal with chlorine or pH test kits.
Pool pumps typically disperse chlorine into the water for you, but it is possible to add chlorine without a pump. The easiest way to do this is with chlorine tablets.
Running your filter after shocking your pool is a must and is just as important to your pool as shocking it is. Be sure to run your filter for at least 6 hours, but shoot for 24 hours to several days, if your pool is particularly dirty or has algae, to properly circulate the chlorine and clean the water.
Shock your pool at least once per week, or when your Total Chlorine is higher than your Free Chlorine. Apply the shock at night time, as sunlight burns up chlorine and greatly reduces its effectiveness. Run your pump (at night) for at least 8 hours to ensure good distribution.
A pool can only be safe for swimming without a pump for a few days and a maximum of one week. The definite number of days the pool will be safe will also depend on the temperatures of the water, the weather at that particular time, the level of chlorine, and how clean the pool was before the pump stopped functioning.
Floating pool dispensers can be used in aboveground and inground pools, but make sure your pool manufacturer says it's safe to use one. The chlorine floater must be removed from the water when people are in the pool.
For the greatest protection against algae, bacteria, and cloudy water, Intex pools should maintain a chlorine level of 2.0-4.0 ppm at all times. If you opted for the Intex Salt Chlorinator, you can make your own chlorine by adding the correct amount of Pool Salt to the water.
Skimmer Net
With excessive debris in the water like leaves, pine needles, and dirt, the pool walls will get slimy and grow mildew faster.
For most inflatable pools or plastic kiddie pools following the guidelines listed above, the water should be changed every two weeks at a minimum. If you are not adding chlorine to kill bacteria, drain the pool every other day. Stagnant water without chlorine can become unhealthy water in as little as 24-48 hours.
Before getting in
Don't swim or let others swim if sick with diarrhea. Shower for at least 1 minute before you get into the water to remove dirt or anything else on your body.
How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
Aim to maintain a chlorine level of 3 to 5mg/l at all times. How frequently you add more chlorine will depend on your usage and bathing habits. It could be daily, every two to three days or weekly. For 1mg/l, add 2g per 1000 litres.
2 ppm of Chlorine will take up to 4 and a half days or around 110 hours to evaporate from 10 gallons of standing water. Ultraviolet light, water circulation, and aeration will speed up the evaporation process dramatically. Chlorine will last between 6 and 8 minutes in 10 gallons of boiling tap water.
The most important factor though is the size of the pool. You'll need about 52-104 oz of liquid chlorine per 10,000 gallons of water. This amount should get the chlorine level to between 5 and 10 ppm.
Chemicals that you add to your pool while the water is circulating don't need to be recirculated; they will stay mixed even if you don't pump the water continually. Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time.