Adding chlorine besides the shock can increase the chlorine content in the water which can make the entire shocking process useless. Hence, it is better if you don't use the shock and chlorine at the same time. The best time to add chlorine to the pool water is after you have shocked the pool.
It is best to wait before going into the pool because liquid chlorine levels will be high after shocking, but it will be safe to swim after only 24 hours. Each chlorine compound is designed for a specific purpose. Using these two types in conjunction with one another will keep your pool clean, clear and sparkling!
Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock. Without tabs, the chlorine shock will dissipate quickly out of the water; without shock, the chlorine level will not get high enough to fully sanitize the water.
You can add granular chlorine stabilizer (CYA) to the pool water using the skimmer. Liquid cyanuric acid can be mixed in a bucket of water first and then poured into the pool or skimmer.
Incompatible Pool Chemicals
Mixing of organic chlorinating agents (such as trichloroisocyanuric acid) and inorganic chlorinating agents (such as sodium hypochlorite) can lead to fires, explosions and chlorine gas release.
You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool. It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
If your total chlorine level is high, you will use a non-chlorine shock; if it is low, you will use a chlorinated shock. As a rule, you will need to raise free chlorine to 10 times your combined chlorine to hit what is known as “break point.” Therefore, it is good to deal with combined chlorine while it is still small.
How much chlorine do you need to shock a pool? Unfortunately, you can't shock your pool using your regular 3-inch chlorine tablets. Common chlorine sanitizing products are great for maintaining chlorine levels, but not necessarily eliminating new waste, bacteria and algae.
And how long do you have to wait before you can swim? You should wait one hour per pound of shock product added, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool.
When you shock a pool, you test and adjust the pH level for a reason. With that said, if you shock a pool outside of the 7.2 to 7.4 pH range, not only will you waste a significant amount of the chlorine used, you will also end up with cloudy water.
Chlorine has a low pH level, and in order to maintain your pool water's clarity and balance, shocking weekly will allow you to quickly raise the chlorine level, which will rid the pool of contaminants, without lowering the water's pH levels.
The best time of day to shock pool is when the sun is down. So, experts recommend shocking your pool in the evening or at night, to make sure it does its job. Shocking during the day can be ineffective as UV rays from direct sunlight significantly reduce free chlorine levels.
Keep your pump and filter running. Give the shock a good 12 to 24 hours to work it's magic. If the algae hasn't cleared up after 24-48 hours, clean and brush the pool and add another shock treatment.
If the pool is still very cloudy or green, you may need to shock it to make it safe to swim in again. First, make sure that the filter system is working properly and the chemicals are still at the proper levels. Next, mix up your chlorine shock (hyperchlorinate) treatment.
Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
Liquid chlorine is generally less costly than granular shock and comes in refillable containers, where granular shock does not. Liquid chlorine does not need to dissolve in your water as it is already in liquid form. In addition, liquid chlorine is non-scaling and leaves no residue.
Light Green or Teal Pool Water:
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.
BUT, if you have to shock your pool during the day in broad daylight, you can still swim after adding shock. It's recommended that you wait one hour after adding shock with the filter running, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool.
Measure 17g of non-chlorine shock per 1500 litres or 35g of chlorine shock per 1500 litres (consult the label instructions as this can vary based on chemical quality and brand). Carefully add the required shock to the hot tub. Leave the cover off for approximately 20 minutes.
Such interaction produces a toxic gas that is dangerous to health even in small amounts. A good rule of thumb is to never mix pool chemicals with each other. After adding Calcium Hypochlorite a user should always wait 24 hours before adding chemicals that would alter their pH.
The Orderly Addition of Chemicals
If both the pH and total alkalinity levels are too high, you'll need to add pH reducer. Once you get your pH levels between 7.2 and 7.5 and your total alkalinity between 60 and 120 ppm you can move on to working on the calcium hardness and chlorine levels.
TEST IN THE MORNING
If you are having chlorine issues in your pool, the best time to get a water sample is in the morning. Even with proper amounts of chlorine stabilizer, chlorine will burn-off during the day. Testing in the morning will give your water a chance to circulate all night and avoid the sun's UV rays.
Chlorine issues often cause cloudy water. Adding a recommended dose of pool shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
Final Thoughts. Running your filter after shocking your pool is a must and is just as important to your pool as shocking it is. Be sure to run your filter for at least 6 hours, but shoot for 24 hours to several days, if your pool is particularly dirty or has algae, to properly circulate the chlorine and clean the water ...
Let the pump run for about 6 hours or more and test the water. Don't use the pool right away – wait for the free chlorine levels to drop to 1 – 3 ppm before it is safe to swim.