The best time of day to shock your pool is in the evening. This is because the sun's rays can affect the effectiveness of the chlorine by dissolving it too quickly, before it has a chance to rid the pool of contaminants and clean the water.
Sun Down – You'll want to shock your pool in the evening when the sun has gone down. This gives your pool plenty of time during the night to free the chlorine and clean the water. In the morning, you should be able to enjoy your pool. If you shock your pool during the day, the sun's UV rays will dissolve the chlorine.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
If the pool is still very cloudy or green, you may need to shock it to make it safe to swim in again. First, make sure that the filter system is working properly and the chemicals are still at the proper levels. Next, mix up your chlorine shock (hyperchlorinate) treatment.
To be on the safe side, you may also consider shocking your pool every 1-2 weeks as a preventative measure. If you're utilizing a saltwater system with your swimming pool, it's also a good idea to periodically shock your swimming pool if the chlorine levels are low.
It's pretty tough to over-shock your pool; shocking your pool two days in a row with the proper dosage for your pool volume shouldn't be a problem – and in fact, is sometimes even needed to rid your pool of algae and other contaminants.
Never close the cover immediately after shocking the pool. It is recommended to wait several hours before closing the cover. Use a test kit to regularly test the pool water. If the tests results are good, this does not imply the water chemistry was good prior to your current test results.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
However, after shocking the pool, you shouldn't vacuum for at least 24 hours. Running the water pump during this period will allow the shock to do its job.
Although, if you overdo the shock treatment, you risk getting green hair from chlorine due to the excess chlorine oxidizing the copper in the water. You can execute a shock treatment with a few different types of pool shock, just be mindful of how much you're using.
It is recommended that chlorine be added at the end of the day once the sun has set and there are no more bathers in the pool.
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
So if you buy liquid shock, be aware that it only lasts one to two months at the most before it starts to lose effectiveness. While many swimming pool chemicals stay good for years if stored correctly, some pool-maintenance supplies expire more quickly.
Is It Safe To Run The pool Pump With The Pool Cover On? It is safe to run the pool pump and filter with a swimming pool cover on. The pool cover doesn't in any way stop or hinder the pool pump from circulating the water or carrying out its function.
Maintaining chlorine levels of 10ppm or higher for extended periods of time can not only ruin your liner and cover but also severely damage your pool equipment. Chlorine should be maintained ideally between 1.5ppm to 3ppm.
You want some clear area between the edge of the pool and the cover to pour chemicals. You don't need to remove the cover, you just need enough room so you aren't splashing any full strength chemicals on the cover. When you are done with the chemical addition you can pull the cover back into place.
Brown pool water is often caused by metals (iron) becoming oxidized in the pool water. If you shocked your pool water and it turned brown you probably have metals. Oxidized iron usually turns a brown or rusty color in the water.
Algae will remain in your pool after shock if you've had insufficient chlorine and an overabundance of metal elements in the pool water. Therefore, to start the cleaning process. Remove all the debris from the pool with a leaf net and then let the smaller dirt fragments settle.
Causes of Rising Alkalinity
It's also not uncommon for pool owners to go a bit overboard when shocking their pool, and since chlorine-based pool shock is a high-alkaline substance, it will also naturally raise your pool alkalinity.
It's recommended that you should do a pool shock once a week. The more you use the pool, the more often you need to shock it. Occasionally, you may need to perform an extra pool shock after: Heavy pool use, like a pool party.
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.
So, not only is shocking a saltwater pool okay, but it's actually important to your pool's health. Shocking is the process in which you overload your pool with chlorine (3-5 times the normal amount) to improve your pool's cleanliness and kill off organic matter.
Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool. Short answer: No. Chlorine sanitizers and shock are similar but different in strength.