Although pool pumps are usually waterproof and designed to withstand rain and splashes, they are not designed to be submerged in standing water. If your pump is located in a spot that has been known to flood, you should unplug your pump before rain and switch it off at the breaker.
No, you can leave it out. It will be fine.
Keep it on a low shelf so it won't fall or roll. If you keep your motor outdoors all winter, you could build a 'lean-to' with lumber or plastic for snow, rain and tree branches, but keep good air flow around the motor, and don't wrap it in plastic, which traps moisture inside the motor.
Pump motors can develop rust deep inside the motor which can keep the motor for working come springtime. Keeping pumps away from accumulating moisture (assuming you live in a place that gets considerable rain/snowfall) during the winter is a good way to protect the equipment.
First of all, you do not have to enclose your pool equipment (pump, filter, heater). A lot of people camouflage it with landscaping or a small fence, so that is not visible. Pool equipment is designed to be outdoors. As long it is taken care of and properly winterized at time of pool closing, it need not be covered.
Even if you turn off the power to your pool equipment, it can still be damaged by wind, rain, and debris. To avoid damage, we recommend covering pool equipment with a large plastic tarp or waterproof coverings. Ensure that the covering is tied down tightly to avoid water from getting to the equipment.
We recommend that our customers run their pumps rain or shine UNLESS we have an electrical storm. In that case, lightning could strike an outside circuit, which could damage your pump and other equipment. If you're worried about lightening, turn the pump off or shut off the breaker.
Pool pump and rain
You should keep the pump dry and out of the rain. Rain that is allowed to fall on the pump can get into the motor and cause a short circuit, burning out the motor in the process. Cover the pump and never allow water to fall on it from above.
Although completely waterproof, the Intex Pool Pump is designed to sit on the ground outside of the pool so that it doesn't get damaged by people swimming or playing in the pool.
A good guideline is 8-10 hours a day. On the cooler days and early and late season, you can cut the run time down to 4-6 hours because there is usually less swimmers and cooler water requires less chemicals.
Chemicals that you add to your pool while the water is circulating don't need to be recirculated; they will stay mixed even if you don't pump the water continually. Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time.
The rule of thumb is generally 8 hours, although it could be anywhere from 6-12 hours, depending on your pool's size. Each pool is unique, so to keep your pool pump efficient and effective, you need to figure out exactly what your pool's turnover rate is.
Protect the pump motor from water damage
In addition to removing circuit breakers, consider moving the motor indoors or covering it with a waterproof material to prevent water from getting inside.
Give your pool a good shock treatment 1 to 2 days before the storm hits. You can bring the chlorine level up pretty high to prolong the pool being depleted of chlorine. Run the pool for about 24hrs after the shock treatment to allow the treatment to make its way throughout the entire pool.
It's best to run your pool pump during the day
Not only does sunlight give fuel for algae to grow, it also destroys your pool chlorine and this is why you should always run your pool during the day!
One of the most significant consumers of energy in homes with swimming pools are pool pumps, which keep pools clean by circulating water through filters. Pool pumps can consume 3,000 to over 5,000 kWh per year.
The size of your pool, the efficiency of your pump and filter, and how dirty your pool is are just some of the factors you need to consider. Nevertheless, most pool cleaning professionals would advise against running a pool pump for more than 8 hours a day.
It may be cheaper to run the pump at night, but honestly you should run it 1 hour a day per 10 degrees of temperature at least, and it should be during the day. Running the pump at night should only be when you are doing a major chemical treatment such as algae clean-up.
One very important rule to remember: Just because pool water is clear doesn't mean it is sanitary or in proper chemical balance. Depending on the size of your pool, we still recommend the pump run 8-10 hours per day during the hottest summer months and at least 6 hours per day during the winter months.
As long as necessary. The point of running your pool pump in the winter is to keep your water moving, which prevents it from freezing should temperatures get too low. So ideally, run your pump (and keep it running) whenever temperatures start getting close to 32 degrees Fahrenheit, the freezing point of water.
Dry running occurs when a pump operates without adequate liquid. This leads to a surge in pressure, flow or overheating that will instigate a pump failure. As a result, the pumping elements seize up on the shaft.
Pool pumps run dry for a variety of reasons, but two particular causes are common and easily avoided. If the water level of the pool is too low, the pump cannot pull in the water efficiently or at all. Also, the pool's pump basket can get obstructed, causing water flow to ease or stop altogether.
The most common reason for low or no flow is that the baskets are full of debris. By checking and emptying both the skimmer basket (by the pool) and the pump basket (inside the pump) will free up the water flow, allowing the system to fully 'prime' and function at full capacity.
The most reliable way to protect your pump against dry running is to install external conductivity probe with a switch. This system shuts off the pump before the pump draws in air, providing 100% protection against damage.