Similar to cleaning pavers with muriatic acid, avoid an intense concentration of bleach, as it can damage the pavers.
Whether your patio is sealed concrete or cement, or even sealed concrete pavers, a bleach and water solution makes it easy to clean away built up soil, stains from leaves and pollen, mold, mildew and algae.
Apply the bleach and water to the wet paving slabs
Brush the solution to make sure you get an equal coverage of the cleaner. Make sure you brush the cleaner into all corners of the paving slabs. Once applied leave the cleaner on the surface for 10 -15 minutes.
Bleach: This alkaline solution may be effective for other household uses, but it can discolor concrete pavers that have been colored or stained.
Usually, hosing them down once a month is sufficient. Use soap and water, if the pavers are still dirty after sweeping and water hosing, make a solution of soap and water. You can use dish soap, laundry detergent, or any type of general-purpose cleaner. Never use bleach on your pavers, as it can damage the surface.
A dish soap, like Dawn, is a safe place to start. The surfactants in dish soaps are designed to remove oil and grease, they're gentle enough to be used without issue on your pavers. In a bowl or bucket, mix the soap with water and pour it onto the stain and agitate. Rinse and repeat if needed.
A solution of household bleach diluted 10:1 with water (10 parts water) can be used to remove many types of stains. Some of these include beverage stains, leaf, wood rot, and tobacco stains. Always test a small section of your patio before covering a large area.
Use Bleach
But that's not all; chlorine bleach can also be used for cleaning the concrete driveway. Of course, you should dilute it with equal parts of water or a 1:1 ratio. With the mixture ready, spray it on the driveway, allowing it to sit for 10 minutes. Then, use a stiff brush before rinsing with clean water.
As a gentler cleaner, bleach can't harm concrete's durable material. Aside from being an effective cleaner and stain remover, it also acts as a disinfectant to the concrete surface.
White vinegar is good for cleaning pavers, though it's also acidic enough to erode the stones' surface. Diluted vinegar can be used safely to clean paving stones, though it should be used sparingly and infrequently to protect your paving from damage.
Dilute white vinegar with water in a bucket, at Walmart (a 50:50 solution is fine), and apply this natural, eco-friendly cleaning solution to the paving slabs with a firm brush and rinse thoroughly.
OxiClean is a powerful concrete cleaner that works well on various materials, including pavement and grout. This concentrated solution provides excellent cleaning without leaving residue.
Dry brushing with or without application of clean sharp sand. OR High pressure water jetting with or without detergent. OR Apply fungicides. Use ordinary bleach or calcium chloride followed by sodium hypochlorite dissolved in water (1kg in 5 litres) then scrub with stiff brush.
Be sure to rinse away all traces of the sodium hypochlorite solution. Allow the patio to dry: Allow the patio to air dry completely before replacing any furniture or other items.
You can also choose to scrub your patio with oxygen bleach like OxiClean. Add two scoops of oxygen bleach to a gallon of water. Cover the bricks. Allow it to sit for 10 minutes.
In fact, vinegar removes mold from concrete better than bleach. Bleach will only remove the top layer of mold, causing the mold to return.
Bleach is commonly used to whiten concrete and is very effective at doing so if the initial stain is removed beforehand. Bleaching stained concrete white prepares it for any additional coloring treatments that you may wish to apply in the future.
Leave the Bleach on the Pavers
Allow the bleach to sit on the pavers for about 10-20 minutes. This will help to disinfect and clean the surface. It will also help remove any stains that are tough to remove and mold.
Prepare the solution diluting ½ cup bleach in 1 qt. warm water. Add 1 tsp liquid dish soap. This will help enhance the bleach's ability to remove tough stains from the pavers and will help rinse away dirt.
When bleach is left to air dry on floors and is not rinsed away, it can leave behind bleach crystals after the bleach evaporates. Sodium hypochlorite will break down into salt and water when left to do so. Since undiluted bleach is mostly water to begin with, once the floor dries, salt crystals will be left behind.
For lightly soiled concrete, you can remove dirt by using bleach mixed with water. Add 1/8th cup of liquid dishwashing detergent to the solution and pour it into a spray bottle. Spray the solution onto the surface, and let it sit for a few minutes. Scrub with a nylon-bristled brush.
The pressure washer in combination with a dirt cutter is an excellent option. This removes not only weeds and moss from the surface, but also from indentations. Keeping up with this type of cleaning means that there is less time for weeds to grow. It also helps to maintain the beauty of the paving stones' surface.
Although bleach is great at the whitening effect, you can use peroxide to achieve this. Hydrogen peroxide is an oxygenated bleach. It is safe for plants, so when you rinse this solution, it won't harm anything. It works together with the dish soap and baking soda to remove dirt and whiten dirty concrete.
Simple Green is one of the best cleaning products for dirty pavers. It doesn't have any harmful chemicals that could possibly warp your precious driveway. Less chemicals mean there's a less likely chance your paver stones will change to a weird-looking color.