Why won't my whirlpool washer complete a cycle?

Author: Josianne Durgan  |  Last update: Wednesday, April 30, 2025

Fortunately, there are several potential causes that have easy fixes such as blocked drain pumps/hoses, worn out belts, faulty motors and malfunctioning lid switches that are all relatively simple repairs if addressed correctly by either yourself or an experienced professional repair technician who specializes in ...

Why won't my washing machine finish its cycle?

If your washer in the washing machine is stuck on one continuous cycle and will not progress and move forward to the other wash cycle, then most likely the timer is faulty and needs replacement. The timer on your washing machine controls all aspects of the wash, spin and others.

How do I reset my Whirlpool washer cycle?

Turn the washer off. Set the mode selector dial to NORMAL. Turn the dial counter clockwise ONE click (LEFT), clockwise THREE clicks (RIGHT), counter clockwise ONE click (LEFT) then clockwise ONE click (RIGHT). Now press the start button.

Why won't my washing machine move to the next cycle?

Many washers won't move to the next cycle until they drain. If there's standing water in your appliance (which may or may not cause it to just keep running), it's not good. Check your washer's drain hose to ensure it's not clogged, kinked, or blocked.

Why won't my Whirlpool washer go past the sensing cycle?

Try to press and hold the start button for 5 seconds to reset the cycle. You have already tried to unplug the unit and that didn't reset anything, so if holding the start button doesn't reset the washer, you'll need to call warranty. You either have a bad shift actuator below the tub, or the control board is failing.

How to Do a Whirlpool Washer Reset & Recalibration

Why won t my washing machine go past sensing fill?

The first component to check is the water inlet valve. The valve opens to ensure the correct volume of water enters your washer. If defective, water will be blocked from entering your washer and might get stuck on the “Sensing Fill” stage of the cycle.

Why does my Whirlpool washer keep stopping during the cycle?

The first step is to check the power supply. This can be done by simply making sure your washing machine is plugged into the power socket correctly. It's not uncommon for a plug to become loose or damaged over time, which might cause it to turn your washer off mid-cycle.

Why is my washing machine not advancing through the cycle?

If your washer does not advance through the cycle or stalls at a wash or rinse fill portion, then the water inlet valve may be at fault. You should first verify that the inlet hoses do not have any kinks or restrictions and that the inlet screens are clean.

How to fix a washing machine stuck on cycle?

Reset the Washer: Unplug the washer for a few minutes, then plug it back in to reset the electronics. Check Cycle Settings: Ensure the cycle selector is correctly set and not stuck between cycles. Inspect the Lid Switch: Many washers have a lid switch that prevents operation if the lid is open.

Why is my washing machine not draining and finishing cycle?

Common Reasons Your Washing Machine Won't Drain

Clogged pump. Kinked drain hose. Broken pump. Broken lid switch.

What is the most common problem with Whirlpool washers?

A start button on your washer's control panel not working despite the rest of the lights coming on is the most common Whirlpool washer issue you will encounter. Taking off the control panel to try and find the cause will let you see if the solution can be DIYed, or a professional needs to be called.

Does Whirlpool have a reset button?

Many Whirlpool dryers have a reset button, but the location and appearance of the button can vary depending on the model of your dryer. In some cases, the reset button may be located on the control panel, while in others it may be located on the back of the dryer.

How do you force a washing machine to reset?

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

How to fix a washer that stops mid-cycle?

For most machines, you can perform a master reset by unplugging your machine for one minute, this may correct an electrical fault. If your machine is not full of water, try quickly opening and closing your machine door 6 times in 12 seconds. Most machines understand this as a machine reset.

Why is my washing machine not cycling?

Normally, your washing machine won't go into a spin cycle until it's been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.

How do I reset my washer if it will not go through all cycles?

Turn the washing machine off at the powerpoint for at least 60 seconds, and then turn it back on. With a little luck, the master reset should restart the wash programs. Run a short cycle: If you think the problem is your clothes physically jamming the lock, you can set the washer to run another short cycle.

Can you reset a washing machine by unplugging it?

If you're encountering issues with your washing machine, a simple reset might do the trick. While you can often simply unplug your machine, wait a minute, and plug it back in, there are a few other tips, depending on your issue.

Why does my washing machine stop cycle?

If the washing machine suddenly stops working in the middle of a cycle and does not display an error code, this could be due to a problem with the water supply or drains.

Why is my whirlpool washer stuck in the spin cycle?

Fortunately, there are several potential causes that have easy fixes such as blocked drain pumps/hoses, worn out belts, faulty motors and malfunctioning lid switches that are all relatively simple repairs if addressed correctly by either yourself or an experienced professional repair technician who specializes in ...

Why is my washing machine stuck on a cycle?

A surprising number of washing machine pauses can be traced back to a simple issue with the door latch. Most machines have a safety feature that stops the cycle if triggered! So, do a visual inspection and look for any signs of obstruction or damage or if the alignment is a little off.

Why won't my washer finish a load?

When your washing machine is failing to finish its wash cycle, it is recommended to check the heater. If the heater - also known as a heating element has failed then you can perform a few checks to confirm the fault.

Why is my whirlpool washer stuck on sensing?

Your washer may remain stuck on the sensing cycle because it is unable to adjust the water levels in the washer due to the failure of the water valves. Browse our selection of genuine Whirlpool OEM water inlet valves to find a new one for your washer.

What is the most common problem with a Whirlpool washer front?

Worn tub bearings are common problems in Whirlpool front load washers. After 10 years, a tub bearing can wear out and prevent the tub from rotating properly.

Previous article
How do I estimate carpet removal?
Next article
How do the Amish get ice?