Your sand filter is designed to operate effectively with a certain level of sand in it. When the sand level in the filter housing or sand tank is too high, then you may notice sand coming out of the backwash lines when you backwash or use the rinse function.
Your pump may be too large or the sand level too high in the filter. When the filter is backwashing the water flow can cause the sand to rise high enough and overflow into the standpipe, which will allow the sand back into the pool.
If you believe the sand is from your filter, then the most likely problem with your sand filter is a cracked lateral. Laterals are tubes at the bottom of your filter (you can see them here). Water filters through the sand and is collected by these laterals and then shot through standing pipe and back into your pool.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
Too much sand and your filter will likely not run correctly or may break when reassembling. Too little sand and you will have cloudy water no matter how much your filter runs.
How Often Should You Backwash a Pool Sand Filter? As a general rule of thumb, you should backwash and rinse your filter about once a fortnight. The optimal time is right after you vacuum the pool. However, if your pool has had a lot more use than normal, it may be necessary to backwash once a week.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
Do not operate your filter pump without having the D.E. powder coating the grids, or you will see the filter pressure rise very quickly, and if left in this manner the grids can collapse or the fabric can become clogged or damaged. As the pressure gauge on a D.E. filter increases, flow rate decreases.
Adding too much DE to your pool may cause multiple negative results. These ramifications include a clogged skimmer, turning the pool cloudy, reducing the circulatory pressure in the pool and putting too much work on your pump that may result in eventually breaking the pump.
During backwashing, the water flows in reverse, from bottom to top, out of the laterals and up thru the sand, to flush out the trapped dirt from the sand bed, and send it out the waste line. Sand filters can have either a push-pull valve (also known as a slide valve) or a multiport valve.
Add diatomaceous earth (DE) to your pool skimmer, stick to around a scoop or two – no more than the size of a 1lb coffee cup. The moment you do this, go to the pool jets to see if it is returning DE into the pool, or if the water suddenly looks cloudy. If it is, you likely have an issue with your filter.
After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear. Shut off the pump motor and push the T-handle back down into locked position. Turn your pump back on and note the lower pressure.
Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.
If your swimming pool begins to seem a bit cloudy or unclear, then you may have a sand filter that's running slowly. This can happen even though your sand filter looks fine and seems to be running as it should. It can look like how it's supposed to but not be filtering debris from your pool as it should.
What Is Backwashing? The backwashing process reverses the flow of water to flush out contaminants from a swimming pool filter. It should be carried out until water runs clear through the waste line.
Yes, we recommend backwashing after you vacuum your pool. This allows the filter to shoot out any dirt / debris you have vacuumed up. Don't forget to set your filter to “rinse” for 30 seconds after backwashing!
Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.
Your filter may be clean and normal at 9-10 psi, but your neighbor's filter gauge could run higher, and be clean at 15-16 psi. Some systems with very low resistance can run very low pressures, barely registering, while other filter systems can run quite high, pushing 30 psi when the filter becomes dirty.
If the handle on top is parallel to the valve, it's open. Likewise, if the handle is perpendicular to the top, the valve is closed. Common places you might find a ball valve are in irrigation and in sites where you need to control water supply from one area to another.
Chemically, it is safe to swim. You will need circulation in the pool to introduce chlorine...... keeping it sanitary and algae free. Do not turn your pump off for more than 24 hours or so.
After backwashing, new DE must be added to the filter. Add the entire amount of DE the filter recommends. If you see DE returning to the pool, vacuum it to waste, after it settles. The next time you backwash and recoat, decrease the amount by 1 pound.
The most common reasons why a cartridge, sand, or DE filter's pressure rises quickly, even after cleaning or backwashing, is a clogged or blocked filter, algae or old filter elements. If any of these things are wrong, the pressure can rise rapidly in minutes, hours or days.
Why Is Dirt Coming Out Pool Jets? If dirt is returning to your pool through the return jets (sometimes known as eyeballs), this is another sign that something in your pool's system is wrong. It can be an indicator of broken laterals (in a sand filter) or that the filter needs backwashing.
Generally speaking, a pressure reading between 10 – 25 psi can be considered normal. Once you have installed a new filter, turn everything on and take a baseline reading. Each time that you change your pool filter take a new baseline reading.