High doses of chlorine, like pool shock, can cause temporary cloudiness as it kills contaminants. High levels of pH, alkalinity, and calcium hardness are more likely to cause cloudy water.
If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock. In this case, you should take another reading of free chlorine and do the shocking again using liquid chlorine (sodium hypochlorite).
In most cases, a cloudy pool after shocking is only temporary and should clear up within 24 hours. Keep filtering your pool, add a little clarifier to help, and your pool should be clear in no time. If after 24 hours your pool is not clear, then you may need to look a little deeper for the solution.
1) After shock - Sometimes pool water looks cloudy right after you apply shock granules such as cal-hypo, or liquid shock, but rest assured it's only temporary. This could be due to change in water balance – meaning your pool water temporarily goes off balance when adding these products.
Wait until the chlorine level in the water drops down to 1-4 parts per million (ppm) before allowing swimmers back into the pool. If the water still looks a little cloudy after the shock treatment, you may want to use a water clarifier before allowing swimmers back into the pool.
In theory, if you have a cloudy swimming pool, you can add chlorine to “shock it” and clear things up. Chlorine will get the job done. But, the amounts may vary and you may have to really pound the pool with chlorine to get the water totally clear.
Excessive levels of pool chemicals can cause your water to become cloudy. High pH, high alkalinity, high chlorine or other sanitisers, and high calcium hardness are all common culprits.
However, sometimes a balanced pool will become cloudy immediately after being shocked. This typically clears quickly on its own and shouldn't be considered a problem. Environmental factors include pretty much everything around the pool like severe weather, wildlife, construction, trees, pool algae, and people.
For the most part, yes. It can be unattractive and it should be addressed, but it is mostly safe to swim in cloudy water. The only exception would be if the pool is cloudy because there are too many chemicals in it. This pool water would be unsafe to swim in and should be avoided.
Pool chemicals could be out of balance or the pH might be off. Chlorine levels and the right pH are key to keeping a pool clear. If a pool's pump or the filter isn't working right, the water may look murkier than usual. Storms or increased rainfall can affect your pool.
The water's pH may be too low or too high.
Lower than 7 indicates an acidic pool, but higher than 7.8 is too alkaline. A pool measuring at either extreme will likely be cloudy. High pH often indicates excess calcium deposits, and low pH often indicates more chloramine and less free chlorine.
If the chlorine smell is very strong, however, you may soon spot “red-eyed” swimmers emerging from the pool. That's when the pool water is assumed to have “too much chlorine” in it. Ironically, a strong chemical smell around the pool and “swimmer red eye” may be signs that there is not enough chlorine in the water.
Skim the top of the pool for debris that may have settled on the pool surface. Add one pound of diluted granular shock to the water for every 7,000 gallons of pool water. Run the filter for 24 hours and retest the water. The slimy looking film can be an early onset of algae.
What happens if too much shock is added? You cannot overshock a swimming pool or add too much. Adding too much shock or overshocking your pool will kill off algae. The negative of adding too much shock is it will upset the chemical balance of your pool.
Chlorine at high levels is corrosive so it's not a matter of if, but when. In particular, the chlorine dissolves the rubber and corrodes the plastic parts of pool cleaners, pumps and filters. It can also damage pool heater internals, as well as valves and rubber seals. This damage can be expensive.
Rapid pH Change
It drastically raises the pH in the water around it, which leads to clouding. This explains why the cloudiness does not happen all at once, rather the process creates a cloudy plume that slowly expands across the pool.
The simple answer is No. Baking soda cannot be used to clear up a cloudy pool because it is a base. Bases raise PH levels, which causes the water to turn cloudy. Some people suggest using baking soda as a quick fix to high alkalinity levels, but it's not reliable as a pool chemical.
When the pH levels are imbalanced, it renders the free chlorine ineffective and the levels decrease. Too little free chlorine forms chloramine and it is this combined chlorine that results in your pool's cloudy appearance.
pH Up is sodium carbonate which will increase both pH AND Total Alkalinity (TA). If your water is close to being saturated with calcium carbonate already, then adding this product can not only cloud the water, but it will remain cloudy for some time.
Here is why: Sunlight is white, which is made up of all the colours of the spectrum. The molecules in pool water absorb light from the red end of the spectrum when sunlight falls on the water. By removing the red, the light which ends up being reflected has a slightly blue hue which can vary in richness by water depth.
But is it safe to swim in a pool with algae? Whether mild or severe, it isn't recommended. Significant amounts of swimming pool algae welcome a breeding ground of harmful bacteria that feed on algae. These bacteria pose health risks to swimmers, most commonly resulting in a skin rash.
It is important to know what exactly bleach is before you put it in your pool. Household bleach, Clorox and liquid chlorine can all be used to sanitize a pool. They are all types of chlorine. Household bleaches such as Clorox usually contain about 5-6% available chlorine, about half that of pool liquid chlorine.