Control Panel: Unresponsive buttons If your Whirlpool dishwasher still isn't starting, the issue might be with the control panel or touchpad. Ensure the buttons or touch-sensitive areas are clean and free of debris. If the control panel still doesn't respond, it may need to be repaired or replaced.
Make sure the dishwasher is in Standby mode (no cycle running). Press the "Heated Dry," and "Normal," buttons one after the other, twice. After entering the correct button sequence, the control panel should light up as the dishwasher begins the reset.
Try this first - unplug or shut off breaker to dishwasher for 5 minutes, then power back on - if you still are NOT able to get buttons to work to change cycles, look for a control lock button on the panel - press and HOLD it for 3 to 5 seconds to UNLOCK the panel.
Most common problems with Whirlpool dishwashers
The dishwasher does not drain properly. The detergent cup is not working properly. The dishwasher is not filling with water. The dishwasher door is leaking.
Dishwashers usually don't have a dedicated reset button on the control panel. You can reset your dishwasher by unplugging it from its power source for one minute and then plugging it back in.
There are several easy options that may be causing your dishwasher control panel to not work, including the following: The dishwasher control panel needs to be reset. The dishwasher control panel problem is caused by a lack of power. A child lock has been activated, causing your dishwasher control panel problems.
Some models require you to shut off the power to the dishwasher either by unplugging it or shutting off the circuit breaker. Others are reset by pressing and holding the Start/Reset button on the control panel, then waiting a few moments before attempting to start a wash cycle.
When your dishwasher won't start, begin troubleshooting by looking at the most common causes: lack of power, broken door latch, defective timer switch, and blown thermal fuse. If it's not those things, you may need to replace the motor starter relay or drive motor instead.
Many Whirlpool dryers have a reset button, but the location and appearance of the button can vary depending on the model of your dryer. In some cases, the reset button may be located on the control panel, while in others it may be located on the back of the dryer.
Control Panel: Unresponsive buttons
If your Whirlpool dishwasher still isn't starting, the issue might be with the control panel or touchpad. Ensure the buttons or touch-sensitive areas are clean and free of debris. If the control panel still doesn't respond, it may need to be repaired or replaced.
Several factors can contribute to this, including: Power Issues: The dishwasher might not be plugged in, the circuit breaker could have tripped, or there might be a blown fuse. Door Latch: As mentioned earlier, if the door doesn't latch correctly, the dishwasher won't start as a safety measure.
Hold the start/reset button – If unplugging the dishwasher didn't work, the next thing you can try is pressing and holding the start or reset button for at least one full minute. All you have to do now is cross your fingers and hope it works.
Whirlpool Dishwasher Control Panel
If lights are illuminated or some of the control works, it's likely the control panel is faulty and will need to be replaced. If no lights and no functionality is present, it's more likely a line fuse or main control board is at fault.
If the dishwasher won't start but has power, it could be stuck between cycles. If the start button has been pushed more than once, the dishwasher may revert to a drain cycle. To remedy this, allow the drain cycle to run, let it sit for 60 to 90 seconds, then press the start button once.
If the dishwasher buttons aren't working, it's possible the door latch is malfunctioning and preventing a wash cycle from being started. Inspect the door latch for any damage. you can also use a multimeter to test the micro switch inside the door latch for electrical continuity.
There are several signs that your dishwasher's control board may be faulty. The most obvious sign is that your dishwasher won't turn on or won't respond to your commands. You may also notice that your dishwasher is running for longer than usual or that it's not cleaning your dishes properly.
To reset a dishwasher, you need to hold the start button down for three seconds or, failing that, switch your dishwasher off at the main power supply. If that won't sort out the glitch, you may have problems with your power, water source, door latch, or internal issues.
Control Panel - The control panel is the interface for operating the dishwasher. If it fails, you won't be able to select a cycle. The average cost to fix a control panel is around $250, with a range of $200 to $400.