The thermostat may have a dead battery, so replace them with fresh ones and try again. Your furnace may turn on right away after this. If it doesn't, you may have a faulty power circuit. Have an HVAC professional diagnose this issue, and provide you with professional recommendations.
If your furnace won't kick on when you turn the thermostat up, it could be due to a variety of reasons such as a tripped circuit breaker, a faulty thermostat, or a problem with the furnace itself like a malfunctioning igniter or gas valve. Checking these components might help you figure out the issue.
If nothing's happening when you're expecting the whir of a blower, check the circuit breaker and fuse. At your electrical panel, make sure all switches related to the HVAC system are on. Reset any tripped breakers and replace all blown fuses, and your furnace should kick back on.
There are several reasons why your furnace may not turn on. The most common include a broken thermostat, gas line issues, clogged air filters, blocked ductwork, a tripped circuit breaker, and issues with the furnace itself.
The cause of your furnace not blowing hot air could be the thermostat configuration, a dirty air filter, the high limit switch, a clogged condensate line, insufficient fuel, leaky ducts, ignition problems, a blocked burner, flame sensor issues, gas valve malfunctions, a cracked heat exchanger, or a clogged coil.
No power: If the thermostat isn't working at all, there could be a power issue. Try checking the circuit breaker box or replacing the batteries. Bad wiring: The thermostat may be unresponsive if the wiring has gone bad. Remove the cover and check inside for loose, detached, or corroded wires.
Checking your thermostat is the best place to start. Make sure it's set to “heat” and that you've set the temperature higher than the current room temperature. If that doesn't resolve the problem, try switching your fan to “on” to force the furnace to start working.
Your thermostat is responsible for telling your furnace when to turn on and off. So if your thermostat is not set or working properly, it might never tell your furnace to kick on. The first thing you'll want to check is your thermostat's settings.
If your boiler stops responding to your thermostat or heating controls, it's worth checking the batteries. Not all thermostats use batteries - some are wired into the mains but have backup batteries in case your power fails. If you've experienced a power cut, your thermostat's backup battery might've run out.
Check/Clean the Ignitor
A pilot ignitor coated in debris won't ignite the furnace, even if the thermostat clicks on and sends the right signal. To access the ignitor, remove the furnace's front panel. Identify whether the ignitor is dirty or clogged.
There is usually a small reset button somewhere on the thermostat. Finding this button may require that the thermostat panel be removed and pressing this button may require something like a paperclip to push. Hold the reset button down for 5 seconds and the thermostat should reset.
In most newer systems, the button is often directly next to the blower motor, while in older systems, it may be harder to spot as it is sometimes underneath or behind the motor. The reset button is often made of yellow or red plastic and marked with a large “R ” to make it easier to spot.
Make sure your WiFi router is powered and broadcasting. Restart your router by pressing the OFF/ON button or by unplugging the device from the socket for approximately 5 seconds and plugging it back in. If the problem persists, please reset your thermostat.
The standard thermostat is hardwired to communicate with the furnace, air conditioner and/or the heat pump. Typically, a home thermostat utilizes five wires that connect to HVAC components and power. These wires are color-coded for easy identification.
The thermostat may have a dead battery, so replace them with fresh ones and try again. Your furnace may turn on right away after this. If it doesn't, you may have a faulty power circuit. Have an HVAC professional diagnose this issue, and provide you with professional recommendations.
If your furnace doesn't switch on, the circuit breaker could be shut off. Check your circuit breaker panel to make sure all switches for your HVAC system are set to “ON.” Check Your Thermostat: If your furnace doesn't turn on automatically, the thermostat may have lost its programming or reset.
While it may be tempting to simply turn on the furnace and start heating up your house, it is important to make sure your HVAC system is working properly and safely.
Check the Power Source Sometimes the problem between the thermostat and your furnace is as simple as replacing the batteries. Many digital thermostats use standard batteries to power their functions. Also make sure to check there is power at the furnace as well.
Thermostat issues are one of the most common culprits of furnace malfunctions. If your furnace isn't working as well as it should, and you've determined that other issues such as a faulty furnace heat exchanger or dirty air filters aren't to blame, you should inspect and troubleshoot your thermostat.
The average cost of a new thermostat, including installation, ranges in price from $50 to $500 or more based on several factors including the type of thermostat, labor costs, the complexity of the installation, and more.
HVAC System Suddenly Quits Working
If the thermostat's display is dark, a lack of power may be the issue. Try replacing the batteries, then check for a blown fuse or tripped breaker in the electrical panel. If the thermostat is still unresponsive, make sure the breaker is shut off and remove the cover.
Slowly turn the thermostat from off to heat and increase the temperature. Both the thermostat and furnace should make a sound. The problem lies in the appliance that does not make a sound.
If your thermostat won't turn on the heat in your home, change out the batteries and see if that fixes the problem. If not, your faulty thermostat could be the result of the following: A tripped breaker. Loose wiring.