Damaged wiring can cause your oven to not heat after self-cleaning. Wires can be melted and damaged if the self-clean cycle gets too hot. The wiring on an oven is located behind a back panel and it is important for connecting essential parts to the oven's control board.
You likely blew the thermal fuse between the upper and lower ovens, this is very common when you do a self clean. This is going to be an expensive repair for a fuse as the entire oven has to come out and some model the upper oven might need to be separated from the lower.
Try holding in the door button and push the cancel for self cleaning. The oven thinks the door is open. If the latch does not open push the door button in and try pushing the self clean button and then cancel. If this fails then turn off power and see if you can manually move the latch to the open position.
During self-cleaning, the oven gets so hot that it can burn out several parts, and Davis says that pieces like the locking mechanism, thermostat, touch panel, and wires are especially at risk. These damages then require repairs that are tedious and can be very costly—up to around $600, according to Davis.
You can try to turn off the power at the breaker or try to hit cancel and see if it stops. leave it off for 5 minutes even after it stops the oven will need to cool down for 30 minutes or so.
To cancel the self-clean cycle on models with electronic controls, press the Cancel or Clear/Off pad. To cancel the self-clean cycle on models with mechanical timer controls, turn the "Stop" knob to the current time of day. The knob should pop out.
Chemical Oven Cleaners:
Chemical cleaners can leave behind residues and fumes that may affect the taste and safety of your food. Wait Time: Typically, it's recommended to wait at least 1-2 hours after cleaning with a chemical oven cleaner before using the oven again.
❗Fumes from the Oven
While no chemicals are used during the self clean cycle and fumes from burning food debris are not harmful to breathe, they are very unpleasant to smell.
When the cycle is finished, let the oven cool down. Then loosen dirt using a scrub brush or nylon scouring pad. Soak up any remaining water with a sponge or cloth and leave the door open to air-dry the oven. If you have a continuous cleaning oven, wipe up residue at least weekly.
Leaving the racks in during this process can result in warping, discoloration, and even potential damage to the oven's internal components. The self-clean cycle generates extremely high temperatures to break down food residues and spills, turning them into ash. However, this extreme heat can take a toll on oven racks.
Door is locked during the Self-Clean cycle
The oven will need to cool to approximately 200°F (95°C) before the door will open. Allow the oven to cool, for approximately 30-90 minutes, move the latch arm to the left to unlock the door.
Damaged Wiring
If you are a frequent user of the self-clean, when the oven ceases to function, this should be the first issue that is checked after a tripped fuse. Damaged wiring will be very obvious upon visual inspection. Any sign of heat damage will mean it needs repair.
Some users have reported fear and alarm at seeing fires inside their self-cleaning ovens. If large pieces of food or a large amount of grease is inside the oven when the high heat builds up, then there is a chance of fire and flames being seen inside.
Your oven will beep and turn off when the self-clean cycle is complete.
Self-cleaning, often with temperatures that go over 1000°, is a particular problem. The elements and the oven just get so hot — much, much hotter than the 350° to 500° range of normal baking — that sometimes fuses pop and control panels burn out.
“I like to mix a 1/2 cup of baking soda and water to make a paste—I also add a few drops of Dawn dish soap,” said San Angelo. “The baking soda is abrasive and Dawn cuts grease. Spread it on the glass and let sit for 15 minutes. Then take a non-abrasive sponge and scrub.
You'll still have to wipe up any residue, drippings, and other “goodies” that are left over after the self-cleaning finishes. When you start your self-cleaning oven, it is going to get hot. Very hot! The goal is to create enough insulated heat to turn any grease, fat, and anything else that's been leftover into ash.
Using the Self-Clean Cycle Requires Precautions
Those same high temperatures that help your oven clean can produce smoke and fumes. “When you run the cycle, turn on a range hood if you have one and open some windows,” Collomb says.
Step 4: Wipe the oven down
If using a high-heat cycle, your oven will unlock once the self-cleaning is complete and the oven has cooled down. While the oven won't unlock until it has reached cooking temperatures, you should wait until the oven is completely cooled down before wiping it clean.
Heating Cycle: To eliminate any residual fumes, turn on the oven to a moderate temperature (around 200°C or 400°F) for 15-30 minutes. Then, let it cool down. Total Wait Time: You should wait at least 1-2 hours after using chemical cleaners to ensure all fumes have dissipated and residues have burned off.
The only cleaner you'll ever need
1 Degreaser for use all around the home. The ultimate power degreasing properties of this cleaner make it the only cleaner you will ever need. The uses are endless! Elbow Grease® cleans pots, pans, kitchen tops, ovens, microwaves, showers, sinks, BBQs, and much, much more.