Check that the LED option is turned On in the
Ensure that the Status LED switch is in the ON (up) position. The Status LED Switch is the first switch from the left on the back panel of the lock.
Make sure the User Code is correct and that the Kwikset button is pushed after entering the User Code. If the door still won't unlock, use a key to unlock the door. Call technical support for further troubleshooting.
Keypad Of Kwikset SmartCode 888 Smart Lock
At the first looking you might be confused on how to use it but you don't need to worry. Keypad has Backlit on the buttons but it is not very bright so you will probably feel as it should be more bright but it is still much better than having no Backlit.
If the Schlage button turns red, you have entered an incorrect user code. If it does not light up at all, you may have entered too many incorrect codes. Wait 30 seconds and try again.
A: If unlocked, the keypad does not light up; if locked, pressing the "Schlage" button above the keypad illuminates all of the number buttons with a blue backlight.
If lighting is low, press the Schlage button at the top of the lock to illuminate the touchscreen. How do I enter an access code to unlock the door with the touchscreen? To unlock the door using the touchscreen, simply enter your four-digit user code.
Does Kwikset Aura Keypad Light Up? Yes, the keypad lights up. If you push the 1-touch locking button, the keypad will illuminate.
How do I know when the batteries are running low on my Smartclode 909/910 deadbolt? There are two low battery indicators on the unit. The LED light on the interior side of the lock will flash red when the batteries are low. The keypad will also flash red when the batteries are low.
The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open.
If your car has keyless entry, placing your hand on the door handle (or on a button mounted on the handle itself), sends out a signal, and if it detects the keys in your pocket, the door will unlock.
This is usually a sign the battery is running low and needs to be replaced, so start by replacing the battery. It is always easier to do this while the remote is still working. If this doesn't solve the problem, it may be due to interference with another vehicle or a faulty transmitter.
Check that the bolt hole is at least 1” deep so the bolt fully extends. Check that the door closes properly so that when the deadbolt is extended, it is going into the bolt hole and not hitting the deadbolt strike or door frame. Check that the mounting screws securing the exterior keypad are not over-tightened.
Replace batteries with new ones to ensure that lock is properly powered. Typical battery life based on 10 entries per day is 10-12 months if the door is properly aligned and the lock does not encounter interference in lock/unlocking the door. 4.
Remove battery pack. 2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
Eventually, after many months of safeguarding, that smart lock battery will drain. What happens if your smart lock battery dies? The good news is that we call these locks “smart” for a reason. Before their batteries die, most smart locks will let you know that they're running low on juice.
The Status LED blinks every 6 seconds on lock interior to communicate whether the door is locked or unlocked, or if the batteries are low. The Status LED may be turned off inside the Premis app.
In normal operating mode: Amber indicates locked. Green indicates unlocked. Red indicates low battery.
Resolution: Battery Jump Procedure: The emergency battery jump start can be used to unlock the door if the batteries are dead. WARNING: The lock will remain unlocked until you change the battery and relock the door.
Enable/Disable 1-Touch Locking When enabled: Press the Outside Schlage Button to lock the deadbolt. (Default setting). When disabled: Press the Outside Schlage Button and then enter an access code to lock the deadbolt. Change Access Code Length Access codes can be 4 - 8 digits in length.
It provides room for four AA batteries, which Schlage says can last up to six months when the lock is used on Wi-Fi or up to a year if you use it with Thread.