If you are constantly plagued with clogged or slow drains, have a plumber inspect the plumbing to determine if the drain line was properly designed and installed. Both drain pipe venting and slope effect how well drains work. Venting allows air to enter the pipe as water drains away.
If your snaking session yields plenty of hair and soap scum, but still leaves you with a slow drain, there's a good chance that the P-trap is still obstructed. To clear it, plug the overflow hole with a rag and fill the tub drain with hot water, which will help to soften and loosen soap scum.
Corrosion
The chemicals in the product are designed to break own the clog, but if left for too long, they can start to break down the pipes themselves. This can lead to cracks and leaks in the pipes, leading to various issues, including water damage and flooding.
Well, if it's not a clogged sink causing the slow drainage, it's probably a plumbing vent issue. Plumbing vents help regulate air pressure in your plumbing system by allowing air to enter the pipes. However, over time, plumbing vents can become clogged with debris, which can lead to slow drainage and even foul odors.
When you are using a baking soda and vinegar solution to clean out your drain, you are actually causing the rubber and plastic that are used for the drain's pipes to be eaten away by the mixture. Over time, this rubber and plastic will break down, causing the drain to become even more blocked.
Using a snake is also more invasive and time-consuming than using a chemical cleaner is, and can often become a dirty job. When it comes to getting at and removing major clogs or clogs that are deep down in your pipes, however, a plumber's snake is your best bet.
In fact, by continuing to use Drano on a chronic clog, you could be causing severe damage to your home's plumbing system. Thusly, if you choose to use Drano on a clogged sink and the clog returns, do not continue to pour Drano down your sink.
Yes, it is possible for drain cleaners to end up making a clog worse. This can happen for a few reasons. First, the chemicals in drain cleaners can corrode pipes and cause damage over time. This can lead to leaks or even bursting, which can make a clog worse by creating additional blockages.
Bring water to a boil and then pour it down the slow clearing drain (recommended to use a whole kettle) Put half a cup of baking soda into that drain and let it sit for a few minutes. Add 1 cup of vinegar for every 1 cup of hot water you pour down the drain. Cover the drain with a plug and let it sit for 10 minutes.
You should clean your sewer line at least every two years. Getting a sewer line inspection for older homes or those with more trees is a good idea. Basic sewer line clogs and debris can be tackled with a $5 drain snake. More stubborn clogs may require professional cleaning, which costs an average of $325.
If you use the wrong type of drain snake for the drain line, the snake could loop back on itself or scrape the sides of the plumbing pipe, causing damage that could lead to leaks and/or the need to replace the damaged piece of pipe.
Check the vent
If the vent is blocked, it can cause water to drain slowly. You can check the vent outside your house to make sure it's not blocked by leaves or other debris. If you have access to the attic or crawl space, you can also check the vent system there to see if there are any blockages.
A manual drain snake, also known as a plumber's snake or a drain auger, is a small boring tool that rotates slowly as it's physically pushed through a stubborn clog. The terminal end of the device is a corkscrew-shaped hook that is fed into a clogged drain or toilet.
Drano is not only ineffective, but it's also extremely damaging to your plumbing system. The heat created by the chemical reaction is more than your drains are designed to take. Corroded, aging plumbing can easily breakdown. Pipes can split and the glue holding them together can disintegrate.
Using a solution of baking soda, vinegar, and hot water
For more stubborn clogs, a combination of baking soda, vinegar, and hot water may do the trick. Because vinegar is an acid and baking soda is a base, mixing the two will cause a chemical reaction that will create pressure and possibly dislodge the clog.
You can use Drano® Clog Removers to unclog a kitchen sink, bathroom sink, shower or clogged bathtub, but DO NOT use them in toilets. For clogged or slow-running drains, apply the product and let it work 15 minutes, then flush with hot water. For tough problems, allow 30 minutes before flushing.
Simply put, Liquid-Plumr and Drano are not designed for frequent use. Because of the chemicals found in these types of products, you could cause irreparable damage to your pipes.
For use on clogged or slow-running drains, pour half of the bottle (32 oz. size) slowly over drain. For extremely slow-running drains or complete clogs, pour in entire contents of 32 oz. bottle.
A common cause for clogs, especially in kitchen drains, is a buildup of grease. Soap and hot water can be an effective Drano alternative to dissolve grease blockages. Pour roughly ½ to 1 cup of dish soap down the blocked drain. Following this, pour about a gallon of boiling water, taking care not to burn yourself.
Baking Soda and White Vinegar
This mixture is a great green alternative to Drano because most people have these items somewhere in their kitchen. To use this method, pour half a cup of baking soda into the clogged drain and follow it with a half cup of white vinegar.
Damaged Pipes — If your home's drainage system is older and made of galvanized materials, there is a very real chance the steelhead of the plumbing snake can scratch the inside of the pipe. Over time, that scratch will rust and weaken the structure of the pipe, until it bursts from the pressure.