Your freezer indicator lights may not be working because the indicator light may have burned out. Check for disconnected or broken wires to the indicator light before replacing it. The user control and display board might be faulty. However, this is not always the case.
If your chest freezer lights are blinking or won't come on at all, reset them by disconnecting power to the freezer for 30 seconds. Once you reconnect power, if they are still blinking or do not come on, service will be required.
The lights no longer working means that one of your LED light boards has failed. All the light boards are in series so if one of them fails, then they all act up. You'll need to swap out one of the LED boards and if that doesn't fix the issue then re-install the old LED board and try a different one.
The high temperature alarm or the red light indicator will be on when your freezer is connected to the mains for the first time. This means that the temperature inside your appliance is still too warm. Keep your freezer door closed and the light will go out in a few hours.
Check to see if the bulb is burned out, and if it is, replace it with an appliance bulb of the same wattage. If the bulb isn't burned out but the light is still off, there might not be electricity running to the freezer. If this is the case, the safety signal light outside the freezer will also be off.
Check the power supply to ensure it is not damaged and is providing the correct voltage. If your LED strip lights won't turn on, you might need to replace the LED Driver.
Some Chest Freezers may have green, red and yellow lights located on the appliance. The green light is the Power-On light. The red light is the Unsafe Temperature light. The yellow light/switch is the Alarm Reset light.
Yes, Frigidaire freezers usually have a reset button located on the control panel. This button can be used to reset the freezer if it is not functioning properly or if there is a power outage.
The GREEN light indicates that the appliance has an electrical supply. The AMBER light indicates that the Fast Freeze option is on. The light is combined with a switch. The RED light is warning that there is a high temperature inside the cabinet.
In these cases it is normal that the red indicator light goes on. It goes off automatically when the interior temperature reaches approximately 5 degrees F. Yellow = Fast freeze switch. If the yellow indicator light goes on, the compressor continues cooling until it is turned off again.
First, check the indicator light to determine if it is burned out. If the indicator light is not burned out, but the light still doesn't work, the user control and display board might need to be replaced.
First, you can try tightening your light bulb or replacing it. Additionally, you can check your refrigerator door switch to see whether it activates when the fridge door is open. When it comes to other complex issues, such as with the wiring or the socket, you will need to contact a professional for repairs.
The user control and display board might be faulty. However, this is not always the case. Check the indicator light to see whether it's burned out first. If the indicator light isn't burnt out but the light still doesn't work, the user control and display board may need to be replaced.
Food that won't stay frozen may be an obvious sign of a faulty freezer, but signs like excessive frost build-up on the walls or freezer-burnt food can also indicate unstable freezer temperatures. You may also notice your freezer making unusually loud humming, clicking or buzzing noises as parts struggle to operate.
Frozen food should be safe to eat indefinitely if your freezer stays at or below 0°F (-18°C). Freezing your food stops most bacteria from growing.
This tiny button can be found on the main control box or on the light strip itself. Once you locate it, all you need to do is press and hold the button for a few seconds until the light flashes. That's it! Your LED strip light is now reset and ready to go.
Additionally, loose connections can cause an LED light to flicker or stop working altogether. Using the wrong driver for a light fixture can also lead to performance issues; drivers that are too high or low voltage will affect the output of an LED.
If the LED is functional and the lead connections have been made properly, your LED should light up when you test it. If it does not, separate and reconnect the leads and cathode/anode to try again. If your LED does not light up, it may be burnt out or defective.
Turn off the refrigerator and freezer from the control panel. After unplugging the refrigerator, turn off the fridge and freezer using the control panel inside the fridge. To do so, set the controls to “zero" or switch them off entirely. Once you're done, you can plug your refrigerator back into the wall socket.
Temperature Affects Ice Production
The Refrigerator and icemaker must be at proper temperature. The recommended fresh food temperature is 37° Fahrenheit; the freezer recommended temperature is 0° Fahrenheit. The icemaker must reach about 16°Fahrenheit before a cycle will begin.
The most common reasons your Frigidaire freezer display is not working are a malfunctioning electronic control board, bad power supply board or a defective user interface.