Use of a lower quality paint that has inadequate adhesion and flexibility. Over thinning the paint or spreading it too thin. Poor surface preparation, especially when the paint is applied to bare wood without priming. Painting under too cool conditions or in warm, windy conditions that make latex paint dry too fast.
Moisture. One of the main causes of peeling paint is the presence of moisture or water around the paint. This will usually happen when water gets into the wood behind the paint. This separates it from the wall and seeps through the layer of paint.
Our unopened cans have a 2 year shelf life, however, opened containers can last even longer if stored off the ground and in a room temperature area. When you're ready to paint again, stir the paint thoroughly to make sure the consistency and odor seem normal.
Peeling paint is most commonly created when water gets under the paint. Therefore, the most common areas for peeling paint to occur are in the wet areas of a house or building e.g. bathroom, laundry or kitchen. However, there may be other issues with the premises such as excess humidity or a leaky roof.
Touch Ups: Behr paint does not retain its color very well. The few times that I have attempted to touch up with Behr it has not gone well. One time I had to repaint an entire great room because a few small touch ups stuck out like a sore thumb.
Behr manufactures highly rated paints, primers and stains that offer premium quality at a range of price points. Each exterior product is available in a spectrum of colors to help you transform the look of your home.
Durability
The consensus is that, on the topic of Sherwin Williams vs Behr paints, the former is more durable and long-lasting than the latter. This makes Sherwin Williams paints a good choice for areas in your home that have a lot of traffic or if you have kids and pets.
Peeling paint must be removed prior to applying a fresh coat of paint to ensure proper adhesion. For Best Results: Refer to the how-to for guidelines on removing peeling paint. Using a scraper or 100-grit sandpaper, remove any loose, cracked, or peeling paint from the damaged area.
Remove all loose and flaking paint with a scraper or wire brush, sand the surface and feather the edges. If the flaking occurs in multiple layers of paint, use of filler may be necessary. Prime bare timber areas before repainting. Use of a premium quality primer and topcoat should prevent a recurrence of the problem.
Well, an alternative to this drastic action is using a binding primer. A popular choice is Zinsser's Peel Stop, which is a water-based primer that penetrates chalky surfaces and helps to glue-down the edges of cracking and peeling coatings to the substrate so they can be successfully painted over.
You can tell paint has gone bad by the smell and texture. A rancid or sour-smelling paint means your paint has gone bad. In particular, the smell of bad paint is similar to sour milk. Other indicators of expired paint include a lumpy or chunky paint consistency.
LIMITED WARRANTY: For one year from the date of purchase, Behr Paint Company warrants to the original consumer purchaser, (1) that the product meets Behr Paint Company manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications.
Peeling or cracking paint is not just unsightly—it can pose a safety hazard. As soon as you notice a problem, remove the peeling areas and start over with fresh coats of primer and paint.
Surface contamination such as dirt, oil, and grease. Polish residues on the surface, which impair the adhesion of the paint. Excessive movement of the substrate, such as joints, imposing stress on the paint film which can result in cracking which in turn lets in moisture, ultimately resulting in a flaking paint film.
Extreme dryness can prevent the formation of strong adhesive bonds that allow the innermost coating of paint to stick to the surface properly. Similarly to painting highly humid surfaces, extreme dryness causes any newly applied coats of paint to peel.
It can also be caused by the use of an incorrect paint system, poor surface preparation or ageing of the paint system. Flaking is similar to peeling, but with the former the coating tends to be harder and brittle.
Zinsser Peel Stop 1-gal. Water Base Clear Interior/Exterior Binding Primer and Sealer (Case of 4) glues down peeling paint and bind chalky surfaces. Designed to seal cracked and checked surfaces for durability, it helps provide a sound surface.
Peeling paint is never ideal. While homeowners may see peeling paint and realize they have to add painting the shutters or the bathroom walls to their to-do list, those looking to buy a home may have a bigger problem. That's because peeling paint could potentially cost them their mortgage.
Remember, always clean the surface where you wish to apply a coat of paint and allow it to dry properly. This is one of the solutions to avoiding peeling paint later on. Use a damp sponge to wipe away any dust from the sandpaper or oils that may have transferred from your hands to the wall. Allow it to dry completely.
Peel Bond is a great bonding primer that can be used when you need to apply a topcoat over a surface that you are concerned it may not stick to.
Average Lifespan
Behr's water-based paints, for example, should be good for two years, says Ed Edrosa, senior project manager at Behr. Meanwhile, cans from Sherwin-Williams boast a three-year shelf life, says Dennis Fiorilli, director of product excellence at Sherwin-Williams.
The BEHR® Professional Products & Services Program is committed to meeting the nationwide needs of professional painters, contractors, remodelers, and property owners/managers through high-quality products and services.
Professional painters frequently utilize premium paints, such as Benjamin Moore and Sherwin-Williams, for their work. Sherwin-Williams is widely regarded as one of the top paint brands, providing a broad range of premium quality paints, including environmentally friendly options.