A constantly running Flushmate (pressure-assisted) toilet is usually caused by an improperly seated or worn-out flush cartridge, a broken flange, a clogged inlet screen, or incorrect actuator clearance. Follow these specific diagnostic steps to fix the issue.
If sufficient water pressure has been verified and the toilet continues to run-on, the following steps may be required:
The Flushmate recalls involve pressure-assisted flushing systems that can burst at or near the weld seam. This sudden release of stored pressure can shatter the porcelain toilet tank and lift the lid, causing severe impact and laceration hazards, as well as significant property damage.
An intermittently running toilet (often called a "phantom flush") usually happens because a slow leak allows water to drain from the tank into the bowl, forcing the fill valve to turn on and refill the tank automatically.
Signs Your Filter Cartridge Needs Replacement
Valve Replacements: Valve replacements cost $50–$150 and resolve noisy or slow toilets. The fill valve refills the tank after each flush, the shut-off valve controls water flow, and the flush valve controls water coming from the tank to the bowl.
The most common cause of a running toilet is a faulty or worn-out flapper (the rubber valve at the bottom of the tank). Over time, this rubber degrades, cracks, or collects mineral buildup, preventing a proper seal and allowing water to continuously leak into the bowl.
Dish soap has the ability to lubricate and break down the bonds of fats and grease. When poured into the toilet, dish soap helps lubricate the waste causing the clog, while also breaking down its structure, allowing it to easily flow down the drain.
A stuck flapper or flush valve can usually be fixed without turning off the water. Remove the lid of the tank. The flapper or flush valve is located in the center of the tank, at the bottom. It can get stuck in the open position, causing the water in the tank to constantly flush through the bowl.
Customers say the product is generally easy to install, with many finding success through online tutorials. While some users experienced issues with leaks and the need for replacement parts, others praised its reliability and efficiency in water usage.
The primary controversy surrounding Primo Water (now operating as Primo Brands, following its merger with BlueTriton/ReadyRefresh) centers on severe operational failures and deceptive billing practices that triggered consumer class-action lawsuits and investor litigation.
No, you cannot put a Flushmate system into a standard, gravity-fed toilet. Flushmate pressure-assist units require a uniquely shaped, pressure-rated toilet bowl designed to handle the forceful rush of water. Trying to mix these components can cause severe issues:
Common Issues With Pressure-Assisted Toilets
Continuous running or refilling. Leaks from the tank or bowl. Loud noises during or after flushing. Weak or incomplete flushes.
No, a running toilet rarely stops on its own. It will continuously waste water—often hundreds of gallons a day—until you fix the underlying issue in the tank, which is usually a bad flapper or a faulty fill valve.
People put aluminum foil in the toilet as an internet-famous cleaning and maintenance hack, though its actual effectiveness is highly debated. The reasons for doing it generally fall into two categories:
🧼 How It Works: Take a bar of soap (or cut one into smaller pieces). Drop it into the toilet tank—not the bowl. Every flush releases a small amount of soapy water, helping to break down stains and keep the bowl fresh.
Baking soda, borax and tea tree oil combine to make a heavy-duty toilet bowl cleaner.
Mixing baking soda and vinegar in a toilet creates a fizzy chemical reaction that releases carbon dioxide gas. While the bubbling action helps loosen mild grime and neutralize odors, it neutralizes both ingredients into simple salt water and is not strong enough to clear heavy toilet clogs.
A running toilet is almost always caused by a slow leak from the tank into the bowl, which causes the fill valve to turn on and refill the tank.
Whether you can replace a flush valve without removing the tank depends entirely on your toilet's design.
A bad flush or fill valve usually causes a toilet to run constantly, produce weak or phantom flushes, or leak water. These issues waste significant water and can drive up your utility bill if not addressed.
The cost to pull and reset a toilet ranges from $150 to $450 professionally, or $15 to $35 if you do it yourself. The vast majority of this cost is labor, as the main materials needed are an inexpensive wax ring, supply lines, and bolts.