Remember: vacuuming your pool regularly will help keep your pH balanced easier and more controlled. Skim your pool for debris, such as leaves, bugs, etc. and be sure to check your skimmer and empty that regularly as well.
Regular Maintenance will often be once a week, unless you are a pool owner with heavy usage. Getting on a weekly cleaning routine will make vacuumings faster and help keep algae from sporing.
Reasons why dirt might return to your pool through the jets during vacuuming or after backwashing include not rinsing after backwashing, a damaged spider gasket, damaged filter or the pool pump being too large for the filter.
Cleaners aren't meant to stay in the pool 24/7. This is true for all cleaners. Pressure side cleaners run on a schedule every day so why take it out? Leaving the cleaner in the pool 24/7 increases its exposure to corrosive chemicals in the water, such as chlorine or shock.
The suction hose for the vacuum has holes, or it isn't fully connected. Verify that the vacuum hose is firmly inserted into the inlet port at the skimmer; then inspect the hose for cracks or holes. The skimmer filter is dirty.
If there is air in the pump basket, that might indicate a suction side blockage. This could occur anywhere between the pump and the skimmer. This is also indicated by a drop in filter pressure from the normal condition.
Most likely, the key reason is a congested pool filter or skimmer basket, or a clog at the mouth of your pool cleaner. If you own a particularly powerful pool pump or your water-flow is really strong, your cleaner will probably move faster than normal.
The rule of thumb for pool maintenance is to run your pump for eight hours per day.
Ideally, you need to run your robot pool cleaner daily or at least once a day if you're always swimming in it. But if you don't swim in it as much, run it at least once weekly or every two weeks. When you're using a swimming pool cover all the time, you may wash your pool monthly.
However, most people will find that a robotic pool cleaner lasts for at least 3 to 5 years, with some extending the longevity of their machine to 7 years or more with basic maintenance and occasional parts replacement. How much do robotic pool cleaners cost?
If dirt is reappearing at the bottom of your swimming pool after you've vacuumed it your pool's filter may be working poorly. Pool filters often work poorly because they're in need of cleaning. If you have a sand filter for your pool you need to make sure that the sand is sharp and freshened up.
Fine debris such as dust, sand and dirt is carried into a pool on the feet of swimmers or on the breeze. While a skimmer removes larger items such as leaves or insects, fine matter drifts to the bottom of the pool and forms a layer of sediment.
If you vacuumed on waste, you will need to turn your filter to the “rinse” setting, turn on the pump and let it run for about 30 seconds, and then turn the pump back off. Make sure to set your filter back to “filter” after you do this.
The size of your pool, the efficiency of your pump and filter, and how dirty your pool is are just some of the factors you need to consider. Nevertheless, most pool cleaning professionals would advise against running a pool pump for more than 8 hours a day.
It's best to run your pool pump during the day
Not only does sunlight give fuel for algae to grow, it also destroys your pool chlorine and this is why you should always run your pool during the day!
Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Automatic Vacuum
You should allow the vacuum to run until it has cleaned the entire pool, including the bottom and the sides. This averages between two and six hours. The better your pool has been maintained -- for example, if you vacuum every week -- the less time it takes.
You may only need to run the cycle two to three times a week. Leaving the machine in the water during that time exposes it to the elements unnecessarily. This exposure could cause the seals to deteriorate faster, allowing for leaks and damage to the electronic components.
Dolphin pool cleaners are safe to use for the general public, however, (for safety precautions) we do not recommend swimming while the cleaner is in use. What are the ideal operating temperatures for my Dolphin cleaner? Dolphin robotic pool cleaners are best used in temperatures between 43 and 93 degrees.
Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. A proactive, productive and energy-saving maintenance activity is to remove the debris floating on the pool surface with a hand-held skimmer.
Depending on the size of your pool, we still recommend you run your pump run at least 4-6 hours a day during the fall and winter months. The daily cycle can be divided into multiple cycles, but each cycle should be no shorter than 4 hours, for all the water to pass through the filter at least once.
Outside of the air conditioner, the pool pump is the largest electricity consumer in the average pool-containing home. According to the study, at the national average of 11.8 cents per KWh, a pool pump alone can add as much as $300 a year to an electric bill.
If you have a suction pool cleaner that is not moving, check the cleaner hose. It should be firmly attached to the suction line in the skimmer or the cleaner line. If you check these and they are all connected, the next thing to do would be to make sure there are no air leaks in the hose.
The filter sand gets clogged
The most common cause for a Kreepy to stop working is clogged filter sand. This is easy to diagnose because whenever you backwash the pool filter, you'll find that the Kreepy works like a bomb for 10 minutes. Then it gets sluggish and slows down or stops again.