While both types provide insulation, R30 is the better option for maximizing energy savings in areas where heat loss or gain is a major concern. For example, R19 may suffice for interior walls, but R30 is more appropriate for exterior-facing attics or floors.
R19 insulation is a thicker, more robust option—offering higher thermal resistance. Commonly used in colder climates, R19 is well-suited for 2x6 wall assemblies, floors, ceilings, and attics. Benefits: Provides superior thermal protection, contributing to lower energy bills and enhanced comfort in colder regions.
R-Value is a measure of insulation's ability to resist heat traveling through it. The higher the R-Value the better the thermal performance of the insulation.
Heat naturally rises, and without proper insulation, it escapes through your attic, forcing your HVAC system to work harder. 💰 Upgrading insulation can reduce energy costs by up to 30%! ✅ Better insulation = less heat loss in winter and less heat gain in summer.
The recommended amount of attic insulation can vary based on your location and local climate. However, a general guideline is to aim for an insulation level of R-30 to R-60. Here's a breakdown: R-30: Suitable for warmer climates, providing adequate insulation for moderate temperature variations.
While both types provide insulation, R30 is the better option for maximizing energy savings in areas where heat loss or gain is a major concern. For example, R19 may suffice for interior walls, but R30 is more appropriate for exterior-facing attics or floors.
The optimal R-value for most homes is 30, but you can go as high as 38 if you live in a tropical climate. Anything higher than 38 indicates an over-insulated space. While you might think that too much insulation can't be bad, there are some significant consequences to consider.
Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces. Use the JM insulation calculator to determine the recommended R-value for your project, as well as how much insulation you'll need.
Do I Have To Remove Old Insulation? Unless your insulation is wet, moldy or infested with pests, you don't need to remove it before adding insulation on top of it. ENERGY STAR® recommends that you inspect your insulation for signs of mold, mildew, moisture and pest infiltration before making this determination.
While over-insulated attics aren't as common as under-insulated attics, it is possible to put so much insulation in your attic that it has a negative impact.
The thinnest insulation material currently available on the market is the 10mm Aerogel blanket. Its manufacturing technology is highly interesting, and its appearance resembles frozen smoke. For some, aerogel is synonymous with time frozen and suspended in space.
The DOE Insulation Fact Sheet (DOE/CE-0180) can be ordered from the Energy Efficiency and Renewable Energy Clearinghouse or accessed from the Internet at www.ornl.gov/ roofs+walls. Fiberglass and rock wool batts—2x4 walls can hold R-13 or R-15 batts; 2x6 walls can have R-19 or R-21 products.
You can use faced or unfaced batting when installing between the roof rafters of finished attic spaces. When using paper or plastic batting insulation, that moisture barrier should face outward toward the attic space. Even if the attic space is unheated, it's typically warmer than the outside air in winter.
The most common application of R19 Insulation is in a vertical wall framed by 2×6 studs. As mentioned above this is a common code requirement in some parts of the United States.
Thermal Resistance: R-21 polyiso boards offer higher thermal resistance compared to R-19, which makes them more effective at reducing heat transfer in colder climates.
Why Fiberglass Batt Is the Best Attic Insulation Material. Fiberglass batt is considered to be the best insulation for attics.
At first it may seem odd to add insulation for warmth and then purposely allow cold air to enter the attic through vents, but this combination is the key to a durable and energy-efficient home.
SAVINGS AND COMFORT
EPA estimates that homeowners can save an average of 15% on heating and cooling costs (or an average of 11% on total energy costs) by air sealing their homes and adding insulation in attics, floors over crawl spaces and basements.
Faced insulation is ideal for spaces that have no existing insulation, such as exterior walls, attic ceilings, crawl spaces, and exterior basement walls.
You will want to bring up your attic up to R-38:
If your attic has 5-6″ of existing insulation, you'll want to install an R-19 to achieve a total of R-38.
The recommended level for most attics is to insulate to R-38 or about 10 to 14 inches, depending on insulation type.
The thermal barrier of a home should consist of a continuous layer of insulation on all sides—including the lowest floor, the exterior walls, and the ceiling or roof. Doubling the thickness of insulation will double the insulation's R-value, cutting heat loss in half.
Can I put plywood over insulation in the attic? Yes you can install plywood subflooring directly over the floor joists and insulation on your floor. You need to install rigid insulation boards on top of the attic flooring joists and then install plywood over the top.
The best kind of rigid foam insulation is polyisocyanurate, also known as polyiso. It has the highest R-rating of any rigid foam insulation and comes with a reflective foil on both sides, allowing it to act as a radiant barrier as well.