If you're all about the DIY life, we've got just the thing for you. Combine two parts water with one part white vinegar in a spray bottle and you'll be all set with a homemade window cleaner. You can also combine warm water with a few drops of dishwashing soap if you prefer.
Professional window cleaners use a solution made from dish soap and water to achieve a streak-free clean. The key is to use a small amount of soap and distilled water. Some professionals add ammonia to the water for increased cleaning power.
Most Effective: Windex Foaming Glass and Window Cleaner
Using an ammonia-based, foaming formula, this all-purpose cleaner can eliminate even the toughest marks on your glass.
Pull the squeegee down each pane in a single stroke from top to bottom. After each stroke, clean the blade with a rag so it doesn't leave streaks. (If the squeegee squeaks a lot, add a bit more soap to the water.) As above, remove any streaks on the glass with a chamois and dry the muntins and sill with a rag.
Mix equal parts water with gentle dish soap or vinegar and lightly scrub the door using a soft sponge or cloth. If the door is wood, make sure to wipe the door in the direction of the grain. Dry with a heavy duty paper towel or dry cloth. Clean your door fixtures using commercial cleaner.
Many hotels use ammonia-based cleaning solutions because ammonia readily cuts through dirt and soap scum. Because of the way it dries, ammonia also decreases the possibility of streaks on glass.
Quick Instructions for Cleaning Interior Doors
Mix 1 cup of water, ¼ cup of baking soda, and 2 tablespoons of dish soap into the spray bottle. Gently add 1 cup of white vinegar. Allow it to fizz if needed. Spray down the door and allow to sit for 10 or so minutes.
Use Vinegar
Try a 50/50 solution of vinegar and water for a streak-free clean. You can use a spray bottle or dip a rag in the solution, just like you would an ordinary cleaner. If you are worried about the fumes, only use vinegar for outdoor windows or mix a couple drops of essential oils to counteract the smell.
To avoid drips and evaporation, spray Windex® Glass Cleaner on large windows in sections, wiping away the cleaning solution before moving on to the next portion.
Use A Soft Microfibre Cloth
Scratches can blemish and dull the glossy surfaces, and this is very difficult to rectify. Soft microfibre anti-scratch cloths are always the best choice when cleaning kitchen doors and units.
If you're looking to clean your front door, all you need is a bucket of soapy water and a soft cloth. There's no need to use rough or abrasive materials, and you won't want to scrub your composite door.
Windex can be used on glass shower doors to help remove marks and streaks, however it may not be the best option for removing a build up of mineral deposits or soap scum.
It's also best to avoid using scouring pads, abrasive brushes, or sharp objects while cleaning glass shower doors, as these can scratch the glass. While there are many commercial products available for tackling the scum and grime in your shower, you may also want to try some DIY eco-friendly options.
Clean the Glass
Use a clean rag and dip it in water, then clean the surface with this alone. Wipe it dry using a clean cloth or a paper towel, and this will help to remove any dirt before you wash it properly. Next, use a mild solution of warm water and detergent. It should be very weak.
The most common professional window cleaning solution recipe is filtered or distilled water and dish soap. Just a few spoonfuls of dish soap is all that's needed to create foam for gliding and to help break up any grease and dirt on the glass during cleaning.
Traditional methods involves the application of soapy water to a window which is then scrubbed clean. Professional window cleaners use microfiber cleaning sleeves fitted onto a hand held t-shaped bar. The sleeve is then soaked in water mixed with a window cleaning solution and applied to the glass.
Also capable of cleaning a variety of surfaces, use this product to remove light soils and fingerprints from stainless steel, chrome, aluminum, plastic, and acrylic glass.
For a shiny finish, Stillwell suggests applying a couple of coats of Polycrylic in a gloss finish and lightly sanding between coats with a 220-grit paper to remove any particles of dust that may have settled on the wet surface.