Characteristics of R19 Insulation This insulation type is commonly used in exterior walls, attics, and areas where additional insulation is required to maintain comfortable indoor temperatures.
The most common application of R19 Insulation is in a vertical wall framed by 2×6 studs. As mentioned above this is a common code requirement in some parts of the United States. R19 Insulation can also be used in other areas around the home, including floors and crawl spaces.
Yes, but R19 fiberglass insulation is less effective than R13 in a 2x4 wall. The reason is that the individual tiny air pockets within the fiberglass provide the insulation power.
While both types provide insulation, R30 is the better option for maximizing energy savings in areas where heat loss or gain is a major concern. For example, R19 may suffice for interior walls, but R30 is more appropriate for exterior-facing attics or floors.
Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces.
R19 insulation is a thicker, more robust option—offering higher thermal resistance. Commonly used in colder climates, R19 is well-suited for 2x6 wall assemblies, floors, ceilings, and attics.
Insulation Batts
Batt insulation is a type of insulation blanket. These are pre-cut sections of insulation that are usually fiberglass, although cellulose, mineral wool, natural fibers and plastic versions are also available. This type of insulation is the best insulation for unfinished walls, floors and ceilings.
R13 insulation is generally more affordable, which makes it an attractive option for budget-conscious projects. However, R19 insulation offers better long-term advantages because of its higher R-value. Why? Because the R-Value translates to a greater energy savings over time.
Thermablok® Aerogel is a revolutionary advancement in thermal technology offering the thinnest insulation available to prevent thermal and cold bridging. Classed as a Super Insulation, Aerogel has the highest insulation value of any known material with the lowest thermal conductivity value of any solid (0.015W/mK).
If the existing attic insulation is an R-19, you may choose to add another layer of R-19. Two layers of R-19 at 6¼ ” thick will achieve a total R-value of 38. So adding an R-19 batt to an existing R-19 batt will give you a total insulation value of R-38.
Insulation For 2x4 Walls
Use R-13 or R-15 kraft-faced fiberglass or mineral wool insulation rolls for 2x4 stud walls. Wall assemblies, especially those in older homes, are built with two-by-four (2x4) studs. The wall thickness will be 3-1/2 inches, not 4 inches. The width of modern 2x4s is 3-1/2 inches.
The Higher R-Value the Better The higher the number the better job the insulation will do at keeping heat and sound in or out of your home. Cellulouse Insulation has a R-value rating of 3.6-4.0 cubic inches, which is one of the highest ratings in the industry.
Fiberglass and rock wool batts—2x4 walls can hold R-13 or R-15 batts; 2x6 walls can have R-19 or R-21 products.
The answer to these issues may be adding insulation, but that still leaves the question of where to apply additional thermal protection to see the most benefit. While both ceiling and roof insulation will increase your home's resistance to outside temperatures, insulating the ceiling should be your priority.
Fiberglass insulation is the most common type of insulation used for garages. Fiberglass insulation is likely the material you picture when you think insulation — that's right, the fluffy pink stuff. This is because fiberglass is the most commonly used insulation for homes, garages and most other types of buildings.
For example, if you need extra soundproofing or don't want to spend time installing a separate vapor barrier, then face may be the best option for you. However, if cost savings are more important than convenience, then unfaced may be the better choice in this case.
The optimal R-value for most homes is 30, but you can go as high as 38 if you live in a tropical climate. Anything higher than 38 indicates an over-insulated space. While you might think that too much insulation can't be bad, there are some significant consequences to consider.
You will want to bring up your attic up to R-38:
If your attic has 5-6″ of existing insulation, you'll want to install an R-19 to achieve a total of R-38.
R-21 insulation achieves its superior performance with minimal difference in thickness compared to R-19, to make it ideal for applications where space is limited. Cost: R-21 insulation tends to have a higher upfront cost than R-19 due to its improved density and efficiency.
For walls, r13 insulation is a good choice in most instances, and because your basement is below the ground, there's some natural protection from the earth around it.
It is possible to over-insulate your house so much that it can't breathe. The whole point of home insulation is to tightly seal your home's interior. But if it becomes too tightly sealed with too many layers of insulation, moisture can get trapped inside those layers.
In unfinished attic spaces, insulate between and over the floor joists to seal off living spaces below. If the air distribution is in the attic space, then consider insulating the rafters to move the distribution into the conditioned space.