So, let's recap the common reasons why a toilet won't unclog — excessive toilet paper use, non-flushable solids, hard water, and clogs in the main sewer line. Thankfully, they can be prevented via methods like double-flushing, covering the toilet bowl, routine inspections and dealing with tree roots.
Many people think that a forceful push into the plunger is what frees up the clog, but this can often worsen the problem. In fact, pushing the plunger in with enough force can even break the seal of the toilet gasket (the seal between the toilet and the floor where the plumbing exits).
If your clogged toilet does, after a few hours, you may return to a toilet that is overflowing, even though you didn't flush it. Bacteria growth: The water sitting in your toilet can be contaminated with bacteria. By allowing it to sit around for hours, you're giving the opportunity for the bacteria to multiply.
Is it okay to leave a clogged toilet overnight? In most cases, you can leave a clogged toilet overnight. However, calling an emergency plumber near you might be warranted if water starts leaking from the pipes. A simple clog likely won't cause this, but an inexperienced homeowner messing with the plumbing could.
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.
Try To Soften the Clog
Put a soap dish, shampoo, or slivers of bar soap in the bowl. Then heat a gallon of water to the temperature of hot tea, pour into the bowl, and wait about 20 minutes. Baking Soda and Vinegar - Try a safe chemical reaction. Measure one cup of baking soda and pour it into the toilet bowl.
The answer might surprise you: dish soap. Yes, that's right. Dish soap can be your savior when it comes to unclogging toilets quickly and efficiently. Simply pour some dish soap into the clogged toilet bowl and let it sit for about 10-15 minutes.
Ideally, no more than five or 10 minutes. One plumber told us that if plunging goes on any longer, it's time to try a toilet snake or call an expert.
Hydrochloric acid, also known as muriatic acid, is a strong acid that is commonly used to dissolve clogs in drains. This acid works by breaking down organic materials such as hair, grease, and soap scum that can accumulate in pipes and cause blockages.
Use Vinegar, Baking Soda, and Hot Water
Just like with clogged kitchen sinks, these three products can work wonders when dealing with clogged toilets. All you need to do is pour a cup of baking soda, 4 cups of boiling water, and a cup of vinegar into the toilet.
Using a plunger is one of the most effective methods used for unblocking a toilet as it can unclog a wide variety of waste pipes.
Then pull up sharply to disturb the clog and loosen it. Continue vigorously pushing and pulling until the water begins to drain. It may take 15 to 20 cycles before the toilet unclogs. Be patient.
When you are using a baking soda and vinegar solution to clean out your drain, you are actually causing the rubber and plastic that are used for the drain's pipes to be eaten away by the mixture. Over time, this rubber and plastic will break down, causing the drain to become even more blocked.
High Water Pressure with Baking Soda and Vinegar
To do this, use a 2:1 ratio of vinegar to baking soda, and mix it into 60 gallons of water. As you pour the water down the drain, use a drain snake or plunger to dislodge debris that is blocking water flow.
We recommend trying another bottle of this product. However, if the problem continues to persist, you should call a plumber, as there are some plumbing situations that even Liquid-Plumr cannot fix. Know when to call a plumber for clogged drains.
After the water is turned off, try using a conventional plunger to unclog the toilet. Be sure the water covers the cup of the plunger; if it doesn't, you may need to manually control the flapper until enough water enters the bowl.
Start slow and add force as needed. Several gentle pumps will usually work better than a couple of hard pushes. If your blockage is going to come out, it should happen in less than 10 minutes.
Drano is not only ineffective, but it's also extremely damaging to your plumbing system. The heat created by the chemical reaction is more than your drains are designed to take. Corroded, aging plumbing can easily breakdown. Pipes can split and the glue holding them together can disintegrate.
Fill a kettle with water and heat it to a boil. Pour the boiling water down the drain to loosen the clog and warm the pipes. Fill the kettle back up and heat up more water. Pour one cup of baking soda and a solution of one cup water and one cup vinegar down the drain.
For an easy clog, your plumber may get the job done in mere minutes. For a more stubborn or deep-seated clog, the process may take multiple hours.