If you have shocked the pool, and it is still green, you missed the mark. Just keep adding shock until the water turns a blue-grey color, with no hint of green, then add another pound just to be sure. This 'blue-ing' should occur within 5 or 10 minutes of adding the shock, if not, add more.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
If you're trying to clean up a green pool after shocking, you want to run that filter for 24-48 hours. Or possibly longer. Running the filter will cycle all of your pool water through it and pick up algae and other contaminants. It's these contaminants that can cloud your pool or make it look green.
When there is not enough chlorine in your pool water, green algae—which can float freely or attach to the walls and floor of your pool—can grow. Thus, in many cases, the most efficient way to get rid of algae is by shocking your pool water with chlorine.
Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
Baking Soda and Green, Blue, or Yellow Algae
You'll need to use an algaecide to kill the algae and superchlorinate your pool to clear the water. After this treatment, test your pH and alkalinity and add baking soda to raise alkalinity to at least 100 ppm and pH to between 7.2 and 7.8.
The fastest way to clean a green pool is by using pool chemicals and your pool filter. This process usually takes around 4-5 days but you will start noticing a major improvement after 24 hours.
Should the green be due to pollen, there may be little to do in the way of minimizing the discoloration short of erecting a building around the pool. Fortunately, assuming there are no allergies to the pollen, it is safe to swim in a pool with that as the cause for green water.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
Clorox itself recommends using between 100 and 200 ounces of regular-strength bleach per 10,000 gallons of pool water -- one gallon is 128 ounces, and many bottles of bleach are available in one-gallon or half-gallon sizes. Pool professionals tend to recommend more conservative amounts of bleach.
It is important to know what exactly bleach is before you put it in your pool. Household bleach, Clorox and liquid chlorine can all be used to sanitize a pool. They are all types of chlorine. Household bleaches such as Clorox usually contain about 5-6% available chlorine, about half that of pool liquid chlorine.
Just like you run vinegar through your coffee pot to get rid of calcium buildup, white vinegar can wipe away this eyesore in your pool. Mix a 50/50 solution of vinegar and water, dip a sponge or soft cloth into it, and scrub that residue away.
Let the pump run for about 6 hours or more and test the water. Don't use the pool right away – wait for the free chlorine levels to drop to 1 – 3 ppm before it is safe to swim.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
When the levels are properly balanced, chlorine will keep the algae at bay, but the water will slowly begin to turn green as the algae take over if there's not enough. But be careful—adding too much chlorine in pool water can cause those metals to oxidize and turn the pool a different shade of green.
Pre-Dissolve Pool Shock
If you need to dissolve the shock first, fill your bucket roughly ¾ full with warm water. Add the shock to the bucket, and slowly stir until the chemical is as dissolved as possible.
Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.
Use a pool brush to vigorously scrub any pool surfaces covered in algae, including the walls, floors, and steps. Apply a green algaecide according to the directions on the label. Let the water circulate for 24 hours, then brush the pool surfaces again. Vacuum or backwash to remove any remaining dead algae.
The main difference between bleach and chlorine is their strength. Chlorine is much stronger than bleach. To get your pools chlorine level to the point it needs to be to keep the pool looking clean and bright; you will need to use more bleach than you will chlorine.
In theory, if you have a cloudy swimming pool, you can add chlorine to “shock it” and clear things up. Chlorine will get the job done. But, the amounts may vary and you may have to really pound the pool with chlorine to get the water totally clear.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours.