Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
If you have shocked the pool, and it is still green, you missed the mark. Just keep adding shock until the water turns a blue-grey color, with no hint of green, then add another pound just to be sure. This 'blue-ing' should occur within 5 or 10 minutes of adding the shock, if not, add more.
You should start seeing a transformation after 24 hours. If you have green pool water after shock, it is imperative to think about your water and pool safety. Hence, don't use the pool after 24 hours.
You cannot overshock a swimming pool or add too much. Adding too much shock or overshocking your pool will kill off algae. The negative of adding too much shock is it will upset the chemical balance of your pool.
It's pretty tough to over-shock your pool; shocking your pool two days in a row with the proper dosage for your pool volume shouldn't be a problem – and in fact, is sometimes even needed to rid your pool of algae and other contaminants.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
When the levels are properly balanced, chlorine will keep the algae at bay, but the water will slowly begin to turn green as the algae take over if there's not enough. But be careful—adding too much chlorine in pool water can cause those metals to oxidize and turn the pool a different shade of green.
If the pool is still very cloudy or green, you may need to shock it to make it safe to swim in again. First, make sure that the filter system is working properly and the chemicals are still at the proper levels. Next, mix up your chlorine shock (hyperchlorinate) treatment.
ADD POOL CLARIFIER
The change in your pool water colour means that you have successfully eliminated the algae and can now clean it out of your pool. If your water is still green, wait another 24 hours and redo the steps from Days 1 and 2.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.
All you need to do is bypass the filter and pool vacuum for algae to the waste. However, this can only work if you have a multiport system or a waste line system in your cartridge filter. Vacuum the pool to waste after you have set up the waste, and the debris and algae will get out of your pool.
Light Green or Teal Pool Water:
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.
Baking Soda and Green, Blue, or Yellow Algae
You'll need to use an algaecide to kill the algae and superchlorinate your pool to clear the water. After this treatment, test your pH and alkalinity and add baking soda to raise alkalinity to at least 100 ppm and pH to between 7.2 and 7.8.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
It's not a good idea to use pool shock at the same time as clarifier. Some clarifiers are polymer based and the shock can act to break up the polymer causing the clarifier to be ineffective. It's best to shock your pool before and wait a day or two before adding clarifier.
Chlorine is a sanitizer, and (unless you use Baquacil products) is necessary for maintaining a clear and healthy pool. Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly.
Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.
Run the filtration system
While shocking your pool will help kill any germs any algae, it won't actually get rid of them; for that, you need your filter. So be sure to run your pool filter for at least 24 hours.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
Always run the pump when shocking the pool and allow it to circulate for 24 hours. The water should then be a blue or cloudy blue color. Test the water 24 hours after shocking and start adjusting pH and alkalinity levels. The chlorine will still be elevated, but over a few days, it should stabilize.
Run the filter for 24 hours and backwash the pool filter around 4 times during the same day to get faster results. DE filters will clear green pools 50% faster than a sand filter.