The best time of day to shock pool is when the sun is down. So, experts recommend shocking your pool in the evening or at night, to make sure it does its job. Shocking during the day can be ineffective as UV rays from direct sunlight significantly reduce free chlorine levels.
Liquid chlorine is not stabilized and will burn off quickly in sunlight. Therefore, it should be administered in the evening, after the sun has set.
Consisetency is more important. The pump needs to be on 1 hour before you test and 1 hour after you add any chemicals. Evening is best in my opinion so that the raised FC can act on anything in the pool and not be lost to the sun.
The best time of day to shock your pool is in the evening. This is because the sun's rays can affect the effectiveness of the chlorine by dissolving it too quickly, before it has a chance to rid the pool of contaminants and clean the water.
Shocking Your Swimming Pool During The Day
Shocking gets rid of chloramines and helps bring your pool's chlorine levels to a well-balanced 3 parts per million (ppm). But while daytime is great for enjoying your pool, it's the wrong time to shock.
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool. It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours.
Chlorine has a low pH level, and in order to maintain your pool water's clarity and balance, shocking weekly will allow you to quickly raise the chlorine level, which will rid the pool of contaminants, without lowering the water's pH levels.
Sun Down – You'll want to shock your pool in the evening when the sun has gone down. This gives your pool plenty of time during the night to free the chlorine and clean the water. In the morning, you should be able to enjoy your pool. If you shock your pool during the day, the sun's UV rays will dissolve the chlorine.
Shocking your pool isn't necessary, although, it's not a bad idea either. If you get an extremely heavy rain fall, you could shock your pool for good measure. This will help fight off any contaminants that the rain may have brought to your pool.
Chlorine is a sanitizer, and (unless you use Baquacil products) is necessary for maintaining a clear and healthy pool. Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly.
Of course, too much chlorine in pool water can be dangerous. Exposure to over-chlorination can provoke asthma, lung irritation, and potentially skin and eye irritation. As well as being potentially bad for you, it's bad for your pool.
This is the main event in clearing a green pool—killing the algae. Pool shock contains a high level of chlorine that will kill the algae and sanitize the pool. For the best results, use a shock that contains at least 70% available chlorine, and shock the pool twice.
Depending on its levels of content, the evaporation time for chlorine from tap water can be estimated: 2 ppm of Chlorine will take up to 4 and a half days or around 110 hours to evaporate from 10 gallons of standing water.
To properly maintain the water chemistry in your swimming pool, put chlorine tablets in a floating chlorine feeder, and once a week, add 3 lbs of shock to the pool at night. The next morning, add algaecide to the pool. Use test strips twice a week to monitor the levels of the chemicals.
What can happen if you go into a pool too soon after it's been shocked? There are a few potential issues. "Chlorine will react with water to produce an acid," Alan says. "The effects will be different depending on whether chlorine is inhaled or whether there is skin or eye contact."
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
A chlorine level of between 3-5mg/l must be maintained in your hot tub at all times. The addition of chlorine will depend upon usage and bathing habits. It could be daily or every 2-3 days (for 1mg/l add 2g per 1000 litres).
Therefore, you should be testing your pool water's chlorine and pH levels every two weeks. Maintaining proper water chemistry will reduce the amount of work needed when you're ready to start swimming again.
Use a pool net to skim away leaves, dead bugs and debris from the surface of the pool. This will prevent them from falling and settling down in the slime at the bottom, where they can rot and create more algae and bacteria. Skim the pool at least once a day to keep it clean.
If the water is clean and clear, then add about 3 oz of liquid chlorine per 1000 gallons of water – while the pool filter is running. This should give you a chlorine level of about 3 ppm.
Wait times for adding pool chemicals
The wait times between adding pool chemicals is usually around 10 minutes each, as that is also sufficient time for the chemicals to mix in the water. Users also under normal conditions can swim roughly 10 minutes after adding chemicals.
Open your pool under normal procedures, and let the filter run with its normal amount of chemicals. When all the other chemicals, such as chlorine. pH and alkalinity, are balanced, add the chlorine stabilizer. Add the stabilizer only after the filter has been backwashed to ensure it is cycled through a clean filter.
So if the pool water isn't cloudy and the 'dirt' is clinging to the walls after brushing, the problem is likely be yellow/mustard algae. Yellow/ Mustard algae is very resistant to even high chlorine levels and will grow and thrive in a chemically well-balanced pool.