120 degrees Fahrenheit is the safety recommendation against scalding, but 140° is the common default setting. Most experts agree that anything below 120 degrees creates a risk for bacteria to develop inside your water heater from stagnant water, such as legionella that causes Legionnaire's disease.
In the US, the maximum legal temperature for a water heater in a residential setting is 120 degrees. Most folks want to run at 125-130 degrees but be careful. The Federal law that stipulates the max temperature is because of folks, especially kids, getting burned by the water.
Although some manufacturers set water heater thermostats at 140ºF, most households usually only require them to be set at 120ºF, which also slows mineral buildup and corrosion in your water heater and pipes. Water heated at 140ºF also poses a safety hazard—scalding.
The maximum Department of Energy recommended water heater temperature setting you should never exceed is 140 degrees Fahrenheit. The lowest recommended setting should never be below 120 degrees Fahrenheit.
The recommended temperature setting for a water heater is 120 degrees. This temperature is not only energy efficient, but it can also help extend the life of your water heater and reduce the risk of leaks or other malfunctions, saving you money!
Water Heater Temperature Recommendations
120 degrees Fahrenheit is the safety recommendation against scalding, but 140° is the common default setting.
"Hot water is typically described as approximately 110 to 140 degrees," says Channa Ovits, M.D., FAAD, a Westchester, New York-based board-certified dermatologist at Westmed Medical Group, a Summit Health Company. But in terms of a shower, you should never tiptoe over 120 degrees, due to the chance of a burn injury.
Making sure your water heater is always set to at least 120 degrees minimizes this risk, as the water should be hot enough to kill any bacteria. Even though most units will go up to 160 degrees, you really shouldn't ever set the temperature higher than 140 degrees in order to reduce the risk of scalding.
Though the DOE says you can save money on hot water by lowering the maximum temperature of your water heater from 140° F to 120° F, we don't necessarily recommend it. That's because the lower temperature might invite opportunistic bacteria—including Legionella, associated with Legionnaires' disease—to proliferate.
According to most dermatologists, the ideal shower temperature is anywhere between 98°F (37°C) and 104°F (40°C)—and no more than 105 °F (41°C). Rinsing under lukewarm water allows you to stay comfortable and maintain your body temperature while reaping all the benefits of both hot and cold showers.
Raising the temperature setting on your water heater ultimately makes your hot water supply last longer. It will ensure everyone gets a hot shower, with plenty leftover to run your dishwasher and washing machine.
C - 150° F - About 1-1/2 seconds. B - 140° F - Less than 5 seconds. A - 130° F - About 30 seconds. HOT - 120° F - More than 5 minutes. LOW - 80° F - No hazard.
Manufacturers often recommend a hot water heater temperature between 120 to 140°F, and there's a reason for this. The Occupational Safety and Health Administration (OSHA) recommends a recommended hot water temperature of at least 122 degrees to prevent the growth of harmful bacteria.
According to Centers for Disease Control and Prevention (CDC), water temperatures ranging from 130 to 140 degrees Fahrenheit(°F) can eliminate most of the harmful bacteria. However, be warned that these high temperatures can also increase the risk of scalding.
To help prevent bacteria growth, the ASSE recommends keeping the water in your water heater tank at about 135 - 140 degrees Fahrenheit.
Most homeowners should flush their water heaters every 6 months or so, but if you have extremely hard water, you may want to do it more often. Flushing your hot water heater could be necessary as often as every few months depending on the mineral content of your local water supply.
The best temperature setting for a hot water heater is between 120 and 140 degrees. Below 120 degrees, bacteria can develop in the stagnant water sitting in the tank. Above 140 degrees, the water is so hot that you and your family members can be at risk for scalding in as little as two seconds.
Turning your water heater off completely when it's not in use can help you save a small amount of money each month on your energy bills, but the hassle of manually turning your unit off and on typically outweighs the benefits.
Faulty fixtures or leaking connections and pipes can go unnoticed at the water heater because it is not an appliance you see every day. The leaks can become significant and result in an increase in the water usage bill and your energy usage bill.
The recommended setting for this control is 60°C/140°F. (Storing hot water at temperatures of less than 55°C is not advisable due to potential for Legionnaires disease). If the water coming out of your taps is too hot then check this control as it could be set too high.
We recommend always keeping the heater set between 110 and 120 degrees. In the summer, try setting your water heater temperature at the low end of this scale, placing it close to or at 110 degrees.
Anyone can be burned from hot water, but children, the elderly and people with sensitive skin are most vulnerable. For these populations, it's recommended to keep the water heater temperature at 120 to 125 degrees.
Recommended Water Heater Temperature for Safety and Efficiency. Many experts, including the U. S. Department of Energy and the Environmental Protection Agency, recommend that your water heater be set to about 120 degrees Fahrenheit.
Understanding these settings can help when figuring out how to adjust the temp on water heater units. A typically represents around 130°F. B usually corresponds to 140°F. C indicates a temperature of about 150°F or higher.