The flashing that covers the “joint” (space) between the wall above and the roof below is called “counter-flashing”. Usually there is a piece of metal flashing that is layered into the roofing plies and turned vertically up the wall.
Eaves. The eaves of a roof is its lowest horizontal edge. The eaves may terminate flush with the outer face of the wall, in which case it is known as a 'flush eaves'. It may also project out beyond the external wall, with a soffit below.
A headwall is a level junction where a roof meets a wall. This illustration shows proper flashing at a headwall condition. Headwall flashing should extend up behind the exterior wall covering and down over the roof-covering material, as you see here.
The eaves are the edges of the roof that hang over or beyond the vertical walls of a building. Their main purpose is to direct water away from the building itself. Eaves can have decorative or architectural elements!
I you're referring to the space BELOW a roof and ABOVE a ceiling, it's called an attic. Otherwise the space above a roof is called 'air,' and the space below a ceiling is called a 'room'.
There should be small gaps between your roof and the walls of your home, and other buildings. These small gaps let building materials shift, expand, and contract with weather and other outside forces, and they prevent moisture from wicking down walls from roofing and gutter systems.
The eaves of a building are the part of the roof that overhangs the face of the wall. The fascia is the vertical board attached to the roof rafters and the soffit is the underside part of the eave.
The terms coving and cornice are often intertwined. However, there is a slight difference as the term cornice refers to a moulding designed to conceal the joint between the wall and ceiling, whereas coving usually refers to the style and type of cornice profile, usually a simplistic uniform design.
The roof-to-wall connection defines how the roof framing and walls are attached. This connection can be made using a variety of materials such as metal connectors, wood blocks and plywood panels, as well as a mix of both. The connection has a significant effect on how sound travels through the house.
roof space. (ruːf speɪs ) noun. the attic space inside a roof.
Coving Curved junction between wall and ceiling ie.
The fascia board is the one mounted at the point where the roof meets the outer walls of the house and is often called the ROOFLINE. However most people refer to it by the name of the main board that carries the gutter – the fascia or fascias.
The cornice area is where walls and ceilings join.
A gable is the section of the wall located at the end of a pitched roof. They have two sloping sides that come together at a ridge. It will be on the opposite side as the eaves and is also referred to as a rake.
A cornice is a type of moulding which runs along the top lengths of your interior walls, which sits in the join between the walls and the ceiling. Cornices are also commonly known as coving, or crown, bed or cove moulding.
A “builder's gap,” intended to help with attic airflow, is caused when roof decking is not flush with the fascia. This can allow pests and water to enter your home and cause various damages. Flashing or a drip edge can be used to seal this gap.
Eaves: The lower edges of the roof that overhang the walls of a building.
Caulk or Sealant: For the smaller holes, an exterior-grade caulk or sealant will suffice. It needs to be weather-resistant to hold up outdoors. Backer Rod: Fill some parts of the bigger gaps with a backer rod.
The Name Says it All...
Cor-A-Vent's Roof-2-Wall Vent™ does just what is says – it's a complete ventilation package for the tough-to-vent detail where a pitched roof meets a vertical wall. Roof-2-Wall Vent has everything in the box you need to install: 6 (six) 4-foot pcs.
Ceiling moulding, also known as crown moulding or cornice, runs along the top of a room where the wall meets the ceiling. It softens the transition from wall to ceiling. Crown moulding can be simple or intricately detailed. These types of moulding trim can make a room look polished.
An attic (sometimes referred to as a loft) is a space found directly below the pitched roof of a house or other building.
CORNICE – A moulding placed at the junction between a wall and ceiling. DADO – The lower portion of a wall above the skirting when finished in contrast to the remainder of the wall e.g. with wood paneling.
Eave. The eave is the entire section of the roof that protrudes beyond the home's walls. It consists of both the fascia and the soffit. The eave provides the structure to the overhang and determines how far it extends out from the building.
Should there be a gap between the roof and fascia? One of the main purposes of a fascia is to prevent moisture and animals from getting into your roof cavity, so you might be concerned after finding a gap between the fascia and the roof. But don't worry—this is perfectly normal.
The average cost to repair roof eaves is $6 to $20 a linear foot, depending on the material your eaves are made from and how extensive the damage is. Measure your roof eaves by measuring the length of your home along each side where the roof overhangs.