Let water-based stains dry for two to three hours and oil-based stains for four to six hours before applying a polyurethane sealer. The best way to get a smooth finish is to apply the first coat of sealer, let it dry, and then lightly sand the surface with 220-grit sandpaper before applying a second coat.
Step 3: Seal or “finish” the stained wood
Remember, you put the stain on unfinished wood, so you need to seal the stain to protect it. Open and stir your polyurethane then brush a coat on. It will bubble as you brush it on.
Applying a topcoat sealer is not required, but a finish protects the stained wood from scratches and keeps it from fading over time. If applying a polyurethane wood finish with a brush, apply one to two coats. If using a spray can, hold 8 to 12 inches from the surface and apply two or three light coats.
To properly answer your question of “Do you have to seal stained wood?”, the answer is no. However, if you want to protect your wood and give it a polished finish, it's smart to do so. It's worth taking the extra steps and applying a wood stain sealer.
Most solvent or water-based stains just colour the wood. These stains need to be sealed in with a varnish, wax or oil. However, some products marketed as wood stains are all-in-one products that colour and protect / seal the wood.
You should sand after the first coat of water-based stain to flatten any wood grain the water raised, but it's unnecessary after that.
How long do you need to wait before sealing wood after staining? For best results, wait at least 24 hours before sealing the wood. If you are concerned the stain isn't quite dry enough, wait another day before applying poly.
Wait 24 hours before applying sealant. Oil-based wood stains have some advantages over water-based stains. If chemical fumes are not a concern, an oil base may be the right wood stain choice. They dry much more slowly, and slower dry rates allow a more even application.
We always recommend two coats of stain for any wood project, but you should only apply as much stain as the wood can absorb. Extremely dense hardwoods may only be able to absorb one coat of wood stain. The general rule of thumb is to apply only as much deck stain as the wood can absorb.
How to Remove Oil-Based Paint or Stain. For oil-based paints, stains and varnishes, soak the bristles in a cup of mineral spirits or paint thinner in a well-ventilated space for a few minutes. Swirl the bristles through the solution and then remove and lay the brush flat on a rag.
Removal is Not Always Necessary
In some cases, you can get away with leaving the previous coat as it is, as long as you perform the other necessary preparation steps, such as sanding and power washing.
Whether you're using water-based or oil-based stain, you need to allow sufficient time for drying before applying polyurethane, otherwise the stain and the poly will suffer. Wait at least 1-2 hours for water-based and at least 6-24 hours for oil-based.
Some basic rules for staining
1. Keep stains and solutions covered when not in use. 2. After the slides are removed from oven these should be cooled before being put in xylene.
1. Act quickly – scrape off solids with a blunt knife and blot liquids with absorbent paper. Never spot-clean any stain with hot or warm water as it can set the stain.
Answer: Most people like to stain and seal at the same time, although you can come back a week later and seal if you like. If you're going to wait between staining and sealing, just do a light power wash to clean the concrete and let it dry prior to sealing.
Two coats are generally better than one
If the deck has been properly cleaned, it should absorb the first of stain well in to the wood. By applying a second, light coat of material, you will fill up the cell structure of the wood (kind of like topping off the tank) and the project will last longer.
After applying wood stain, it's a good idea to seal it with polyurethane to protect your project. There are several different types of polyurethane products to choose from. It's important to select the one that's right for your project and apply it correctly to achieve the best results.
Outdoor wood stains are water repellant, so they make the wood waterproof, that is protecting it against water and, as a result, against mold. The only problem is that it is a short-term protection. As the stain wears out, the water easily finds a tiny crack to penetrate the wood.
Wood stain is intended to be wiped off immediately after application. If the wood stain remains on the wood, liquid solvents in the stain will evaporate, leaving sticky pigments behind that will never fully dry. To remove tacky wood stain, firmly scrub the piece with mineral spirits.
Whenever water or any stain or finish that contains water comes in contact with wood, it causes the wood fibers to swell, which is called “grain raising” or “raised grain.” After the water has dried the wood feels rough to the touch, and thinly applied finishes also feel rough.
Sand to a coarser grit. To get a darker coloring with any stain when you are wiping off the excess, sand to a coarser grit. More of the colorant will lodge in the sanding scratches, producing a darker effect.
Good news, you can stain wood without sanding the old finish off! But you'll still have to do some prep to make the new gel stain bond properly with the old stain. Start by always cleaning the old finish with a good cleaner and degreaser, like TSP. Be sure to rinse all of that cleaner off before moving on.
While staining creates a rich, deep color that highlights natural wood grain, it does not provide long-term protection. Without a protective top coat, wood can be damaged easily due to contact with water, food, or sharp objects. A polyurethane top coat protects the wood from scratches, stains and water damage.