To determine the maximum sink size for your base cabinet, measure the interior of your cabinet and subtract two to three inches from each dimension. A 36″ base cabinet can handle a 33″ sink at most; a 30″ cabinet should be fitted with a sink no larger than 27″ wide.
Some sinks will be labeled 30" Kitchen sink, but the basin size is in fact 28". [This sink will fit!] While other sinks are named after their TRUE 30" basin size [This will NOT fit]. Which means you CAN fit some "thirty" inch sinks in a 30" kitchen sink base cabinet.
A typical 33 x 22-inch sink will fill a 36-inch base cabinet. If you're replacing a sink, make sure it fits the existing cutout. If the cabinet allows, you may be able to install a larger sink by expanding the cutout. A farmhouse sink may require a special cabinet size.
Measure the opening width under your existing sink (or where the new one will be installed) from left to right. This measurement is your cabinet size. Then, allow at least 2-3 inches on both sides for mounting hardware. For example, a 36" cabinet can accomodate a 30-32" sink.
The most common sink sizes for a 30-inch cabinet are 24 to 27 inches wide. These sizes offer a comfortable fit within the cabinet and provide enough room for daily use.
Where 36'' is a common width for a sink cabinet, the typical measurement here is going to be 24''. You should have roughly 24'' from front to back to work with, which will be enough space for any standard sink. It's unlikely that you run into trouble with this dimension, but it's good to double-check just in case.
A 33" cabinet is outside measurement. Figure 3/4" wall thickness, so the inside measurement of the cabinet is 31½". You can possible squeeze the sink in there. It will be difficult to get at the side clips.
A 33" sink will undermount into a 33" cabinet if you strap or harness, not clip or block, the sink in place. Disregard the sink manufacturer's instructions please; I've done this hundreds of times.It is not a difficult process at all.
In general your sink should be at least 2-3” smaller than your cabinet size. For example, a 36” sink base cabinet can easily fit a 33” sink.
The most common sizes for a kitchen sink are 30" or 33", however a standard size could measure anywhere between 24" and 36" in length. Generally, sinks up to 30" will contain one large single bowl.
OVERHANG - The countertop extends over the edge of the sink on all sides by approximately 1/8" - 1/4". Use caution with this installation to be sure that accessories such as colanders or cutting boards will fit properly.
Kitchen Cabinet Kings
General rule of thumb is actual sink should be 3" in actual width less than the sink base for smooth fit. However if you notch the sides of the cabinet, you should be able to get something as tight as 1.5 less than cabinet to fit.
A 36" sink will fit into a 36" cabinet easily if you strap it in place. Manufacturer's allow for chubby plumber fingers to access clips to tighten. If you eliminate the clips, you eliminate the need for access.
Consider the size of the sink. The base cabinet should be wide enough to accommodate the sink, with additional space on either side for plumbing and dish soap. It should also be deep enough to prevent water from spilling out onto the floor. Think about the type of material you want the cabinet to be made of.
The standard size for a kitchen sink can vary, but a typical size for a single-bowl sink is around 30 to 33 inches in width and 20 to 22 inches in depth. Double-bowl sinks can range from 30 to 48 inches in width, depending on the bowl size and configuration.
The reason for this is to allow for adequate room to work when installing the sink, as well as to avoid potential water damage or mold growth in the cabinetry. The minimum cabinet size needed for your sink will be found on the product page from our website once you search the model like the example shown below.
33-inch sinks are one of the most popular sizes of kitchen sinks for homeowners wanting a sink large enough for bigger pots and pans with ample space for food preparation and cleaning.
A 33" cabinet will only fit a 30" sink.
Undermount sinks are recommended for granite, solid surface and quartz countertops, but may not be as effective with laminate. They can be more expensive than drop-in sinks.
Most any sink can be undermounted. Don't make such a project out of it. The main requirement is adequate support. Do what you need to support it so that the top of it is flush or slightly lower than your 3/4" roughtop.
To determine the maximum sink size for your base cabinet, measure the interior of your cabinet and subtract two to three inches from each dimension. A 36″ base cabinet can handle a 33″ sink at most; a 30″ cabinet should be fitted with a sink no larger than 27″ wide.
Measure the opening width under your existing sink (or where the new one will be installed) from left to right. This measurement is your cabinet size. Then, allow at least 2-3 inches on both sides for mounting hardware. For example, a 36" cabinet can accomodate a 30-32" sink.
The recommended size for a 36" base cabinet is a 33" farmhouse sink or smaller. It is recommended that your base cabinet be 3 inches larger than the size of the farmhouse sink you are considering to install.