There are useful tools for cleaning paving stones, such as joint scrapers, sweepers, and pressure washers. In addition, pavers can be cleaned with a small pickaxe, broom, and garden hose.
Mild detergent and water. If your pavers aren't too dirty, this can be a quick and easy way to clean them without any fancy equipment. Mix some mild dish soap with water in a bucket to create suds, then use a brush or a sponge to scrub the surface of the pavers.
Use a specialist cleaner
Try a specialist cleaner like Wet & Forget, at Walmart, which you spray onto the surface of the paving and leave. It can also be used on steps, fountains, patio umbrellas and other smaller outdoor areas. It's bleach-free and non-acidic but will remove mold, moss and grime without any scrubbing.
Wet The Patio With Water
After it's wet, then add some dish soap or a degreaser to a bucket of water. Using a brush that's stiff, pour some water and soap on the pavers and give it all a scrub. Keep it gentle, and don't go overboard on the scrubbing, so you don't damage any of the surfaces.
To clean paver slabs, you can use a detergent, such as Dawn, or a vinegar-water solution that is gentle enough to effectively clean without causing damage to your concrete pavers.
Can you power wash pavers? Power washing (also known as pressure washing) is also a very effective method by which you can remove dust deposits and various stains from your pavers. Just make sure that the water jet is not directed directly at the joints between the paving stones.
The acetic acid in vinegar is a little stronger than acid rain, so exposing your pavers to this substance can lead to bleaching, corrosion and the loss of protective sealant.
Simple Green is one of the best cleaning products for dirty pavers. It doesn't have any harmful chemicals that could possibly warp your precious driveway. Less chemicals mean there's a less likely chance your paver stones will change to a weird-looking color.
Scrubbing Brush and Bucket
Ahhhh the good old-fashioned scrubbing brush. It's been around for such a long time as it genuinely works. When those bristles are passed over the target surface vigorously enough, it'll remove most dirt and stains.
A mix of water and vinegar is a great combination to remove stubborn dirt and stains. If you want even better results, use this mix with a cleaner solution specific made for pavers or soap and water. Just remember to plan your cleaning on sunny days because if it rains, you might need to redo all the work.
What to Avoid. Scrubbing the pavers down with a wire brush. A wire brush can scratch pavers and remove the sand that interlocks them. Also, don't use a power washer to clean the area.
3) USE A CLEANER FIRST
I used a bleach-free pressure washer concentrate and sprayed it over each section to help loosen the grime before going at it with a higher pressure nozzle. It didn't take long to apply and helps get those stubborn mildew stains out.
Similar to cleaning pavers with muriatic acid, avoid an intense concentration of bleach, as it can damage the pavers.
If the pavers are wet due to a pressure wash, allow them at least 24 hours to air dry. They may need a reseal after a deep clean, which is crucial to wash away residue. Excessive moisture from intense heat can also hinder the sealing process.
OxiClean is a powerful concrete cleaner that works well on various materials, including pavement and grout. This concentrated solution provides excellent cleaning without leaving residue.
Depending on the material of the paver (non-coloured concrete is safe), CLR may be suitable. Always spot test in an inconspicuous area first. Make sure the pavers are not coloured, stamped, sealed or coated.
Simply put, black stains on flagstones are caused by certain types of mold and mildew. These fungi find their way onto the stones either from their spores landing on the stones or from simply extending onto the stones from patches of mold or mildew right beside them—a pretty common occurrence for garden pavers.
Occasionally, some pavers may have a whitish residue upon them. The whitish colored residue is called efflorescence. Efflorescence is a natural by-product from the cement hydration process and can be found in any concrete or mortar product.