Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces. Use the
According to the U.S. Department of Energy, R-values for exterior walls in colder climates should be at least R-13 to R-23. In milder climates, a lower R-value may be sufficient.
no, R19 will not provide better sound attenuation than R-13. In fact, just like thermal properties, it will actually provide less. What you're trying to block are airborne noises. An R11 sound batt will provide the best attenuation in a 2x4 wall compared to any of the fiberglass insulation products.
The higher the R value, the more your mat resists heat loss and the better it insulates you from the cold ground. As a rule of thumb, an R value of 1.0 to 2.0 is fine for summer use but you'd need a rating of 4.0 to 5.0+ for winter camping.
The optimal R-value for most homes is 30, but you can go as high as 38 if you live in a tropical climate. Anything higher than 38 indicates an over-insulated space.
For standard 2x4 walls, which are common in older homes, an R-value of R-15 is considered good, while R-21 is excellent. This can be achieved with high-performance fiberglass batts, dense-packed cellulose, or a combination of cavity insulation and continuous insulation.
R15 insulation offers slightly better thermal insulative properties than R13. Some of its formats are a fraction of an inch thicker than R13, making it more effective at helping with energy efficiency. However, the difference is minimal.
R-values 101
For winter camping, you generally want an R-value of at least 5, while three-season campers only need an R-value of 2 or more for most conditions. R-values are additive, so stacking two pads on top of each other provides an R-value that is more or less the sum of their individual R-values.
If we wish to label the strength of the association, for absolute values of r, 0-0.19 is regarded as very weak, 0.2-0.39 as weak, 0.40-0.59 as moderate, 0.6-0.79 as strong and 0.8-1 as very strong correlation, but these are rather arbitrary limits, and the context of the results should be considered.
The DOE Insulation Fact Sheet (DOE/CE-0180) can be ordered from the Energy Efficiency and Renewable Energy Clearinghouse or accessed from the Internet at www.ornl.gov/ roofs+walls. Fiberglass and rock wool batts—2x4 walls can hold R-13 or R-15 batts; 2x6 walls can have R-19 or R-21 products.
Many factors contribute to the high cost of insulating a new construction home. Between the quality of materials, labor costs, and regulatory compliance, insulation costs can add up quickly. Investing in premium insulation like spray foam is an expensive choice.
What Type of Insulation is for Walls? Fiberglass batts or rolls are the most common insulation products used by DIY homeowners for several reasons. Fiberglass is lightweight and readily available at home improvement stores in various quantities and R-values.
It is possible to over-insulate your house so much that it can't breathe. The whole point of home insulation is to tightly seal your home's interior. But if it becomes too tightly sealed with too many layers of insulation, moisture can get trapped inside those layers. That's when mold starts to grow.
ABOUT INSULATION
The thermal barrier of a home should consist of a continuous layer of insulation on all sides—including the lowest floor, the exterior walls, and the ceiling or roof. Doubling the thickness of insulation will double the insulation's R-value, cutting heat loss in half.
Depending on where you live and the part of your home you're insulating (walls, crawlspace, attic, etc.), you'll need a different R-Value. Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces.
In some fields, such as the social sciences, even a relatively low R-squared value, such as 0.5, could be considered relatively strong. In other fields, the standards for a good R-squared reading can be much higher, such as 0.9 or above.
R-Value is a measure of insulation's ability to resist heat traveling through it. The higher the R-Value the better the thermal performance of the insulation.
Rigid foam board insulation is available in many materials, including polystyrene (R-3.8 to R-5.0), polyurethane (R-5.5 to R-6.5) and polyisocyanurate (R-5.6 to R-8.0). Since it has the highest R-value, rigid foam is typically reserved for foundations and basement walls.
R19 Insulation offers superior thermal insulation compared to R13. With a typical thickness of 6.25 inches, R19 fiberglass is designed for use in 2x6 wall cavities, making them suitable for colder climates where higher thermal resistance is necessary.
Therefore, insulation whose thickness changes for any reason over the years of use will see a decrease in its R-value, thus reducing its insulation effectiveness, and in exceptional cases, dropping to zero.
For walls, r13 insulation is a good choice in most instances, and because your basement is below the ground, there's some natural protection from the earth around it.
Excellent Thermal Performance Owens Corning™ R-15 EcoTouch® insulation is specifically engineered to solve the efficiency problems of exterior 2x4 walls. “High density” means more fibers per square inch. It delivers a higher R-value per square inch in less space than standard insulation products.
Fiberglass insulation is the most common type of insulation used for garages. Fiberglass insulation is likely the material you picture when you think insulation — that's right, the fluffy pink stuff. This is because fiberglass is the most commonly used insulation for homes, garages and most other types of buildings.