There are useful tools for cleaning paving stones, such as joint scrapers, sweepers, and pressure washers. In addition, pavers can be cleaned with a small pickaxe, broom, and garden hose.
Use a specialist cleaner
Try a specialist cleaner like Wet & Forget, at Walmart, which you spray onto the surface of the paving and leave. It can also be used on steps, fountains, patio umbrellas and other smaller outdoor areas. It's bleach-free and non-acidic but will remove mold, moss and grime without any scrubbing.
To clean paver slabs, you can use a detergent, such as Dawn, or a vinegar-water solution that is gentle enough to effectively clean without causing damage to your concrete pavers.
Can you power wash pavers? Power washing (also known as pressure washing) is also a very effective method by which you can remove dust deposits and various stains from your pavers. Just make sure that the water jet is not directed directly at the joints between the paving stones.
White vinegar is good for cleaning pavers, though it's also acidic enough to erode the stones' surface. Diluted vinegar can be used safely to clean paving stones, though it should be used sparingly and infrequently to protect your paving from damage.
Apply the Simple Green solution. Allow the product to soak for a minute or so on heavy soils and greasy spills. Scrub, if necessary. Scrubbing with a soft bristle brush or non-abrasive scrubbing pad provides agitation that will help to loosen soils and will ensure a thoroughly clean, residue free surface.
Pour baking soda on the stained spot, then add a bit of warm water. You can add some detergent or white vinegar for a stronger vinegar solution. Let the mixture sit for at least 1 hour. Scrub the top of the pavers, with extra attention to the gaps between the stones or bricks.
Similar to cleaning pavers with muriatic acid, avoid an intense concentration of bleach, as it can damage the pavers.
The old cleaning solutions are still the best ones, even with pavers. Use your everyday hand soap or dishwashing soap and add in some water to maintain and clean your paver surfaces. Get a bowl or tub of water, put in the appropriate amount of soap, then lightly scrub your paver driveway or walkway using a clean brush.
Dry brushing with or without application of clean sharp sand. OR High pressure water jetting with or without detergent. OR Apply fungicides. Use ordinary bleach or calcium chloride followed by sodium hypochlorite dissolved in water (1kg in 5 litres) then scrub with stiff brush.
You can use a pressure washer on your patio pavers if you want to clean stubborn stains or mildew from them. However, be very careful when doing this! Use a gentle spray and avoid letting the water run down the sides of your pavers, especially if they're set in the sand rather than mortar.
OxiClean is a powerful concrete cleaner that works well on various materials, including pavement and grout. This concentrated solution provides excellent cleaning without leaving residue.
If vinegar does not do the trick, you can also try mixing about a cup of bleach for each gallon of water and using this as your mold-killing spray solution.
If you are prepared to use chemicals to remove algae, lichen and moss from your pavers, it is important that you use plastic sheeting to protect other plants in the vicinity. A solution of one cup bleach to four litres of water should do the trick.
Although bleach is great at the whitening effect, you can use peroxide to achieve this. Hydrogen peroxide is an oxygenated bleach. It is safe for plants, so when you rinse this solution, it won't harm anything. It works together with the dish soap and baking soda to remove dirt and whiten dirty concrete.
3) USE A CLEANER FIRST
I used a bleach-free pressure washer concentrate and sprayed it over each section to help loosen the grime before going at it with a higher pressure nozzle. It didn't take long to apply and helps get those stubborn mildew stains out.
If the pavers are wet due to a pressure wash, allow them at least 24 hours to air dry. They may need a reseal after a deep clean, which is crucial to wash away residue. Excessive moisture from intense heat can also hinder the sealing process.
After you have invested in pavers, whether that be a patio, poolside deck, etc., it is important to seal your pavers in order to protect from the weathering UV rays. These rays, which are known to impact the skin negatively, also impact the surface of your pavers negatively.
Acidic cleaners: Harsh, acid-based cleaning products and stain removers can damage the seal and finish of your concrete pavers. Bleach: This alkaline solution may be effective for other household uses, but it can discolor concrete pavers that have been colored or stained.
A dish soap, like Dawn, is a safe place to start. The surfactants in dish soaps are designed to remove oil and grease, they're gentle enough to be used without issue on your pavers. In a bowl or bucket, mix the soap with water and pour it onto the stain and agitate. Rinse and repeat if needed.