Is There Another Name for Cyanuric Acid? Cyanuric acid is called CYA, pool stabilizer, or conditioner. It's sold separately as conditioner and stabilizer or it's included in chlorine products like trichlor or dichlor.
In the pool industry, Cyanuric Acid is known as chlorine stabilizer or pool conditioner.
Baking Soda is used for raising the total alkalinity of the pool, which is the key to keeping the ph in balance. It's not a stabilizer. That's cyanuric acid.
Yes both cyanuric acid and muriatic acid are both acids but they serve different purposes for the pool owner. Cyanuric acid has the chemical formula CNOH, whereas muriatic acid is a diluted form of hydrochloric acid, HCI.
Conditioner: Conditioner is a name given to a chemical which inhibits the degradation of chlorine by UV light. Other commonly used names for conditioner include: stabilizer, sun-shield, the chemical name cyanuric acid, or the trade name Pad-Con.
Clorox has absolutely NO Cyanuric Acid (CYA) in it nor does it increase CYA at all when you use it. You should show them. It's mostly water, then sodium hypochlorite (i.e. chlorine), and sodium chloride salt, and then a small amount of sodium hydroxide and a very small amount of sodium polyacrylate.
Cyanuric acid (CYA), also called stabilizer or conditioner, is used in pools and spas exposed to the sun to reduce the rate of decomposition of available chlorine by ultraviolet rays in sunlight. Stabilized forms of chlorine, such as dichlor and trichlor, contain CYA in their formulas.
Do you need cyanuric acid in a spa or hot tub? Yes! If you are using a chlorine sanitiser, you do need to use cyanuric acid to get help your chlorine work efficiently. Without cyanuric acid, your chlorine level can drop from the ideal range to zero in less than two hours when exposed to the sun.
Cyanuric acid is raised by adding chlorine stabilizer containing cyanuric acid. The only way to lower cyanuric acid is by replacing water.
Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity. Many commercial pool products for raising alkalinity utilize baking soda as their main active ingredient.
Cyanuric acid is present in drinking water when chemicals commonly referred to as dichlor (anhydrous sodium dichloroisocyanurate or sodium dichloroisocyanurate dihydrate) or trichlor (trichloroisocyanuric acid) are used as alternative free chlorine sources.
Although there are no known adverse health effects associated with high CYA concentrations, most health officials usually limit CYA levels to 100 ppm. Some states recommend a lower level for spas, and some jurisdictions ban the use of CYA altogether.
Sodium bicarbonate will raise your alkalinity and slightly raise your pH-so add small amounts and re-test after a few hours to make sure you hit your mark. Once you TA is balanced, your CL will work effectively and your pH will stabilize.
Saltwater pool manufacturers recommend maintaining cyanuric acid levels around 60-80 ppm. This is a bit higher than the 30-50 ppm range recommended for non-saltwater pools. And if you live in an area where your pool gets a lot of direct sunlight, you may even consider bumping your cyanuric acid up to 80-100 ppm.
Areas exposed to high levels of sunlight should maintain 60 – 80 ppm (parts per million). Pools using an ORP Controller (Oxidation Reduction Potential) such as the AutoPilot Total Control, should maintain 30-50 ppm. Indoor pools do not need cyanuric acid, unless it gets periodic exposure to sunlight.
No, cyanuric acid and baking soda work in very different ways in your pool. Baking soda raises the total alkalinity in your pool. But baking soda does not protect or stabilize your chlorine, like CYA.
The problem with low cyanuric acid is chlorine degrades quickly in the presence of sunlight. Chlorine is rendered completely ineffective within a few hours of sun exposure. If you didn't have cyanuric acid in your pool or it was low, you'll find that you need to add a lot more chlorine to have effective sanitization.
If you are struggling to keep your chlorine levels from dropping, it's important to make sure pH and total alkalinity are in proper range. Also, check your filter. It should be rinsed every 30 days but if you have been using your hot tub more than usual, it might need to be cleaned sooner.
Dichlor, short for Dichloro-S- Triazinetrione, is one type of chlorine available for keeping pool water clean. Similar to trichlor, a different kind of chlorine, dichlor is usually granular but can also be found in tablets. You can buy dichlor in one-pound bags or in bulk.
The CDC's Regulation on Cyanuric Acid: 15 ppm.
The main reason for high CYA levels in your pool is from using too much stabilized chlorine. When the pool water evaporates, CYA remains in the water, much like other chemicals such as salt and calcium. As an example, 1 lb. of trichlor in a 10,000 gallon pool will raise the CYA level by 6 ppm.
All alkaline materials are buffers. Cyanuric acid happens to be the most common buffer found in pool water. In effect, cyanuric acid helps stabilize both chlorine and pH. It binds with chlorine to prevent photolysis and it keeps pH elevated.
Cyanuric acid can be produced by hydrolysis of crude or waste melamine followed by crystallization. Acid waste streams from plants producing these materials contain cyanuric acid and on occasion, dissolved amino-substituted triazines, namely, ammeline, ammelide, and melamine.