High water pressure can cut the lifespan of your appliances, causing you to replace them more often. Additionally, you'll experience more leaking faucets around the home, like in the kitchen sink, a toilet running, or the shower spitting water out even if you haven't taken one recently.
If you're dealing with ongoing high water pressure, you should check on your regulator. You may be able to lower your water pressure by adjusting the regulator, or you might need to replace it with a new one.
If your pressure is higher or lower, then you'll need to install, repair, or adjust your pressure regulator to comply. Adjusting your regulator is easy, as long as it's working properly. Simply tighten the screw down clockwise to increase pressure and counter-clockwise to decrease pressure.
High water pressure can even instantly destroy pipes in your house.
If left untreated, high water pressure can lead to the following plumbing issues: The decreased lifespan of appliances such as your dishwasher and water heater. An increase in energy bills due to increase in amount of water that requires heating. Extensive damage to pipe joints.
Excessive water pressure can wear down your pipes quickly, causing them to crack, buckle, and eventually burst. Not only does it waste gallons of water, but it also inflicts damage to your walls, floors, and ceilings. You might also end up with a flooded home, prompting emergency plumbing services.
Unexplained Water Pools and Dampness
One of the most obvious signs of a burst pipe is the presence of water where it shouldn't be. If you notice puddles forming under sinks, near water pipes, or along walls, it's likely a sign of a leaking or burst pipe. Water stains on ceilings and walls are also telltale signs.
Once you find the main water supply, turn it completely off. Turn all faucets to the 'on' position. Once the water supply is off (you might want to double-check this), turn all the faucets in your home to the 'on' position. This will allow for any trapped air to flow through the water lines.
The required type of PRVs can cost anywhere from $90-$200 and can be purchased at a big box store. A plumber will charge anywhere from $200-$800 for materials and labor but a homeowner with a moderate level of maintenance knowledge might be able to switch out their PRV. Don't water utilities like WCID No.
A sudden increase can be due to a broken pressure regulator or a change in the municipal water supply. Additionally, temperature changes or a burst pipe could cause sudden spikes. If your water pressure increases unexpectedly, it's essential to investigate as soon as possible.
The screw acts as a water pressure regulator. If you tighten the screw the water pressure will be more and if you loosen the screw the water pressure will be less. Turn the screw clockwise to tighten it and increase the pressure, or turn it counterclockwise to decrease the pressure. Do not be too hasty.
High pressure is unlikely to be dangerous, even if it's a lot higher, as your system should have a pressure relief valve that will trigger. However, you should not rely on this to prevent overpressurisation. First, it'll be inefficient, and second, it could be dangerous if the relief valve is faulty or jammed.
Pressures above 80 psi are too high. Whereas low water pressure is more of a nuisance than a serious problem (some fixtures, like washing machines, have minimum pressure requirements), high water pressure carries with it a significantly increased risk of damage to pipes, joints, fixtures and seals.
High water pressure can lead to several problems, a burst pipe being just one. Leaks, appliance malfunctions, and other issues can all be prevented if they are detected promptly.
The national average cost of burst pipe repair is between $200 and $1,000, with most people paying around $500 for a moderate repair with a new section of pipe added. At the low end of the spectrum, for a minor repair that doesn't involve pipe replacement, you can expect to pay $150.
Another way to inspect leaks from hidden pipes is by checking for heat from an area beneath the surface. The heat is produced when pressurized water hits a surface for a long period at high velocity. A professional plumbing company can also use modern technology to detect the sounds of water leaking underground.
Check with your water supplier
It could be that the mains' water pressure has increased, which is an issue with your water network. Call your water company to see if they have set the pressure higher than normal because of maintenance work. You might also find that neighbouring homes have reported the same issue.
Normal water pressure range
If your water pressure is under 40 psi, it's considered low. A psi between 20-30 is considered very low, and under the minimum water pressure required by most building codes. On the other side of the spectrum, water pressure above 80 psi is considered too high.
If, on the other hand, your home's water pressure is high, this can cause many problems such as burst pipes, leaks, or rattling pipes. These issues are likely to increase the amount of water your family is using, which will affect your water bill.
On average, water pressure regulator replacement costs $350 or between $250 and $450. You'll pay an additional $100 to $300 for after-hours, weekends, holidays, or projects with access issues. Also called a pressure-reducing valve, each valve costs $50 to $100 on average, but can hit $200 for most single-family homes.