Adding too much DE to your pool may cause multiple negative results. These ramifications include a clogged skimmer, turning the pool cloudy, reducing the circulatory pressure in the pool and putting too much work on your pump that may result in eventually breaking the pump.
It's essential to replace DE powder in your pool filter regularly to keep your swimming pool from getting cloudy. You also need to be sure you add in the right amount of DE powder. Too much, and your filter can run too slowly or break down. Too little, and you'll get a buildup of dirt which can also ruin your filter.
If you are starting with a brand new DE filter installation or doing a full cleaning meaning you are removing all of the DE fromyour filter grids then you will add 1 lb of D.E. powder for every 10 square feet (Sq. Ft.) of filter area. We suggest doing a full DE filter cleaning 1-2 times per year.
When you get down to it, DE filters will filter much finer particles than other filters, that's why it's clogging - again, it's doing what it's designed to do.
Diatomaceous earth (DE) filters use a powder that attaches itself onto a filter grid inside the filter. If the filter is damaged, the DE powder can pass through the filter and back out the return jet. In turn, your pool turns cloudy and looks muddy – not exactly inviting for a quick dip!
Chemically, it is safe to swim. You will need circulation in the pool to introduce chlorine...... keeping it sanitary and algae free. Do not turn your pump off for more than 24 hours or so.
This leaves your pool a cloudy, muddy-looking mess. Luckily however, the powder usually sinks to the bottom of the pool. The only way to remove the earth from your pool is to vacuum the pool with the filter release valve open. This will allow the earth to flush from the filter.
The most common reasons why a cartridge, sand, or DE filter's pressure rises quickly, even after cleaning or backwashing, is a clogged or blocked filter, algae or old filter elements. If any of these things are wrong, the pressure can rise rapidly in minutes, hours or days.
DE Filter Grids Clogged with Oil
Much is brought in on the wind, or dragged in by swimmers. Pool lubricants and some gel type pool clarifiers can add oils to your pool, which eventually is trapped in the filter grids.
Do not operate your filter pump without having the D.E. powder coating the grids, or you will see the filter pressure rise very quickly, and if left in this manner the grids can collapse or the fabric can become clogged or damaged. As the pressure gauge on a D.E. filter increases, flow rate decreases.
After backwashing, new DE must be added to the filter. Add the entire amount of DE the filter recommends. If you see DE returning to the pool, vacuum it to waste, after it settles. The next time you backwash and recoat, decrease the amount by 1 pound.
You should clean your DE filter at least once every month or whenever you're pounds per square inch is 8 to 10 pounds above the normal starting pressure. Cleaning your DE Filter involves three basic steps: Backwashing, Cleaning the manifold and grid and adding new DE.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
Adding too much DE to your pool may cause multiple negative results. These ramifications include a clogged skimmer, turning the pool cloudy, reducing the circulatory pressure in the pool and putting too much work on your pump that may result in eventually breaking the pump.
Your filter may be clean and normal at 9-10 psi, but your neighbor's filter gauge could run higher, and be clean at 15-16 psi. Some systems with very low resistance can run very low pressures, barely registering, while other filter systems can run quite high, pushing 30 psi when the filter becomes dirty.
Whenever the filter fills up with the dirt/debris it reduces the flow of water to your pool. Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear.
Let the pump run for at least 20-30 minutes to let the D.E. spread evenly over the filter grids.
Depending on how much you have added and the size of your pool, it is generally safe to wait about 4 hours after adding liquid chlorine or until levels reach 5 ppm or lower.
Normally, for a DE filter, rinsing the grids/fingers off with water is sufficient. If there is stuff that won't come off with just water you can soak them in detergent. Ideally, for that, you want to use TSP (trisodium phosphate), but that is often difficult to find.
Those with a DE filter should be opening up their filter and cleaning the grids every three months or more often. DE filter grids can last for four or five years with proper care. During cleaning, the grids need to be looked over for damage.
With proper preventative maintenance, the non wear out parts of a filter should last between 5-10 years as well- these include the band clamps, the internal grids, and plumbing including valves.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.