So… what refrigerant can be mixed with R-22? None. You can't mix refrigerants.
Freon MO99 is the closest capacity match to R-22 compared with most other no-oil change refrigerants.
Freon™ MO99 can be used to retrofit R-22 heat pumps .
Against the Law. Due to the phasing out of R22 in 2020, it is illegal for a contractor to mix refrigerants. Once mixed, the refrigerant can no longer be used and must be incinerated. While it is unlikely to be prosecuted by the EPA for this, it is not a great idea.
Using these retrofit guidelines, many R-22 systems can be retrofitted for use with Freon™ 407C in air conditioning, heat pump applications, and refrigeration applications to allow existing equipment to continue to operate safely and efficiently, even after R-22 is no longer available.
Freon™ MO99 refrigerant is a relatively affordable and eco-friendly alternative for R22 air conditioners. You can use it to revive older systems with little to no refrigerant charge, as well as systems that need replacement components.
The pressure can become high enough for parts of the system to rupture. At the very least, leaks will occur.
The information below will try to dispel some of these myths. Arkema recommends using Forane® 427A (R427A) - The EASY RETROFIT™ for your r-22 retrofit solution. When it comes to drop-ins, the truth is that there are none. The hope of “drop-in” refrigerants has become common over the years.
No, the compressor will fail. These two refrigerants have very different properties. One of R22 and R134a is high pressure and the other is low pressure. They don't mix chemically and don't have the same boiling point, leading to inefficiencies and eventual compressor failure.
No ,R404A works at higher pressure and is much better in absorbing and releasing heat .
On January 1, 2020, the U.S. Environmental Protection Agency (EPA) banned the production and import of R-22. But units manufactured in 2009 and earlier still use R-22 today. Its use will eventually be eliminated in the U.S., so all current and future homeowners must be prepared for the transition.
Can I mix Forane® 427A and R-22? Mixing refrigerants is not recommended as it creates a new refrigerant that is not EPA approved. In addition, it contaminates the R-22. Proper calculation of superheat and subcooling becomes extremely difficult, which could result in damaging the compressor.
As of Jan 1 2020, R22 refrigerant has been completely phased out worldwide due to its harmful effects on the ozone layer. It is no longer being produced. If you're interested in learning how to refill R22 in your air conditioner, it is important to know that this is not something a homeowner can do on their own.
How much will an R-22 to R-410A conversion cost? The actual cost will depend on many things, including where you live, but most of the time R-22 conversions start at around $2,000 and go up from there. The higher end of that range is somewhere around $4,500 to $4,600.
As of January 1, 2020, production and import of R22 refrigerant will be illegal in the United States. Of course, continued use of your air conditioner (AC) or heat pump system using R22 refrigerant is allowed.
As a solution, there are two alternative refrigerants used as substitute refrigerant for R22, namely R290 and R32. The R290 is widely used as working fluid in A/C system of Europe countries; meanwhile in Japan and South East countries, R32 is utilized as substitute refrigerant for R22 and R410A (Yu et al., 2010).
So… what refrigerant can be mixed with R-22? None. You can't mix refrigerants.
R-1234yf systems that control freeze protection by pressure may encounter loss of cooling performance if charged with 100% R-134a. This is due to the requirement of R-134a to have a lower setting of 3.3 psig to achieve freeze protection at 32 F. This may result in a 4-degree F.
R134a and R22
The capacity of R134a is smaller than that of R22, and the pressure is lower than that of R22. Due to these features, an R134a air conditioner with the same capacity must be equipped with a larger compressor with a larger evaporator, condenser, and piping.
R-22 conversion is a process wherein an HVAC professional retrofits an old HVAC system to work using the R410A refrigerant rather than the phased-out R-22. You can't simply replace the refrigerant, because the two systems operate differently.
The biggest problem of using refrigerant R404A to replace refrigerant R22 is the problem of lubricating oil. PVE ester oil must be used to replace the mineral lubricating oil for R22. Ester lubricants have high affinity with water and poor dehydration.
R417A refrigerant is an HFC mixture that serves as a substitute for R22. It is compatible with traditional lubricants. In most cases, the lubricant type does not need to be changed in the event of retrofitting.
You cannot just switch refrigerants because R410-A and R-22 have different chemical properties. R410-A operates at a higher pressure. If you put R410-A into an R-22 system, the parts will rupture due to the increased force.
Where can I buy r22 refrigerant? At HVAC supply stores, HVAC service companies (like D&H AC), and online.
Of all the "no oil change" replacement refrigerants, Freon™ MO99™ offers the closest performance match to R-22.