You should run your pump/filter as long as it takes to keep the pool clean. Some pools have great circulation combined with low use, therefore run times can be quite short. Other pools have lousy circ systems and huge bather loads and even 24/7 filtration has trouble keeping up.
Recirculate - This setting is used to troubleshoot problems with the filter sand and is especially useful if you are battling an algae bloom. The water will circulate in the pool normally, but will bypass the filter sand.
The recirculate setting on a swimming pool filter is actually used to bypass the filter mechanism. Recirculate allows the water to flow out of the pool and back into it again without running through the sand or diatomaceous earth in the filtration system.
Overall, the lessons learned today is you should run your pool pump an average 8 hours a day to properly circulate and clean your water. The pump should push your entire pool in gallons in this 8 hour period of time. Residential pool water only needs to be turned over once daily to have proper filtration.
The lever should be on the 'Filter' setting most of the time. This is the setting that provides normal pool filtration by pushing the water through the filter media (sand, glass beads or D.E) that then traps any dirt and debris before the water is returned to the pool.
You should run your pump/filter as long as it takes to keep the pool clean. Some pools have great circulation combined with low use, therefore run times can be quite short. Other pools have lousy circ systems and huge bather loads and even 24/7 filtration has trouble keeping up.
WASTE/DRAIN: Another filter bypass setting, but this setting sends the water out of the waste pipe (hose), instead of returning it to the pool. This setting is used to lower pool water level or to vacuum to waste, which is best when vacuuming algae or heavy amounts of dusty, silty debris.
How Does It Work? In a pool circulation system, water is drawn from the pool through skimmers and drains by a centrifugal pump. The water passes through a basket in the skimmer and in front of the pump to remove large debris before it gets to the pump's impeller.
Suction cleaners typically run at around 2200-2400 RPM. Heaters require 20 to 40 Gallons Per Minute (GPM) so might run at around half speed or a little higher. You would probably want to run your Spa at up to full speed, 3450, for maximum effect.
Open the air bleeder assembly on your filter and turn pump on. Watch the pressure gauge for spikes. After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear.
If you do have this option, it is highly recommended that whenever you have algae, you will need to vacuum to waste. This option allows you to vacuum the algae up and send it out through the backwash line, avoiding getting algae into your filter sand.
Well, as the name suggests, backwashing involves reversing the flow of water through your filter media, be it Zeoplus, sand, glass pearls or diatomaceous earth (DE). This dislodges dirt and debris that may have become trapped, and flushes it out through your multiport valve waste line.
Running the pump at night should only be when you are doing a major chemical treatment such as algae clean-up. Your pool is more vulnerable during the day, plants don't grow at night the way they do during the day–that's true of ALL plants including Algae.
The size of your pool, the efficiency of your pump and filter, and how dirty your pool is are just some of the factors you need to consider. Nevertheless, most pool cleaning professionals would advise against running a pool pump for more than 8 hours a day.
The most common reason for low or no flow is that the baskets are full of debris. By checking and emptying both the skimmer basket (by the pool) and the pump basket (inside the pump) will free up the water flow, allowing the system to fully 'prime' and function at full capacity.
What Does Circulation Mean? Just like your heart circulates blood throughout your body (weird to say, but it's true), your pump circulates water throughout your greater pool circulation system. This should include every bit of water that exists in your pool.
A pool circulation system draws water in through the skimmers and main drain by the pump. The water passes through the skimmer basket(s) and pump basket to prevent any large debris from getting to the pumps impeller.
Drain/Waste: Opting the drain or waste setting will remove pool water without forcing it through the filter. Backwash: This clears out any debris, dirt and other contaminants that may have accumulated on the filter.
In order to prevent residual blow back into the pool, once you've finished backwashing it's highly advisable to rinse the filter. Just as the backwash lifts and flushes the sand, the rinse resets the sand to its original position for optimum filtration.
Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
High swimming pool filter pressure is usually the result of a lot of particles being filtered out of the swimming pool water. When pressure rises it is time to backwash the filter if you have that option with a sand or diatomacesous earth (DE) filter.
Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.