Vinegar is excellent on glazed porcelain tiles as it brings out its shiny exterior. After mopping, rinse the floor once more using clean water. Make sure to wipe the tile dry with a microfiber cloth to avoid streaking and to prevent water from penetrating the grout.
Grab your bucket and fill it up with 1 gallon of hot water then stir in ¼ cup of white vinegar. Vinegar is a tough yet natural cleaning solution that will surely clean up any messes that may be found on your tile. Go on and mop the floor with your vinegar solution. Or use a large sponge.
Vinegar will slowly dissolve the sealer on the grout and tile, allowing dirt, oils, and stains to penetrate deeper into the grout. Using Vinegar on grout can also cause the grout to breakdown overtime. And, that strong acid could damage the finish on the tile too.
General cleaning of porcelain tiles is a relatively simple process. Regular cleaning (once or twice weekly) is the best way of preventing a build-up of dirt and unsightly stains. This can be accomplished with a simple sweep and vacuum to remove debris, followed by mopping sparingly with warm water.
Even though many people rely on vinegar to clean, we highly recommend you do not use it to clean your tile and grout, because it will end up discoloring your floors.
You can safely use vinegar to clean ceramic or porcelain tiles, whether they are glazed or unglazed. For other types, however, like terracotta, marble or grante, we recommend you look for ph neutral cleaner that will not harm the material.
While vinegar is safe to use on laminate, vinyl, porcelain, and ceramic tile, it is best to use it sparingly since the acid in the vinegar can dissolve the finish on your floor. Therefore, when you are using it on tiled floors, you want to make sure you cut it with water or rinse it completely with water.
For most types of tile, including porcelain and ceramic, you only need one key ingredient: A DIY mixture of warm water and dish soap will do the trick. Follow these steps to clean tiles: Spray the water and dish soap solution on the tile surface. Wipe the area with a damp microfiber towel or cloth.
Vinegar and baking soda produce that oh-so-familiar chemical reaction that powers through buildup and loosens tough stains. While it might seem like it's chewing its way through grime, it's not powerful enough to damage the porcelain finish of the toilet bowl.
The time that white vinegar should sit on the tile before cleaning depends on the severity of the stains or buildup you are trying to remove. In general, it is recommended to let the white vinegar solution sit for at least five to ten minutes to penetrate and dissolve any dirt, grime, or soap scum on the tile surface.
Once a month, mix 1/4 cup white vinegar with two gallons of water (or purchase one of the many suitable commercial cleansers) and apply the solution to the floor with a sponge mop. Rinse with plain water, then dry the surface completely with a clean towel or a microfiber cloth.
The best mop for porcelain tiles
The traditional mop and bucket are hard to improve upon. However, for tech fans, there is the electronic spin mop or the steam mop which will make life easier when it comes to cleaning porcelain tiles.
You can also use Pine-Sol® Original Squirt 'N Mop®. It's safe for wood and hard nonporous surfaces like ceramic and porcelain tiles, and also sealed granite. You can apply this product directly from the bottle over a 3' x 3' area and start mopping.
Though popular for being gentler alternatives to harsh chemical cleaners, baking soda, Borax, and even salt can harm the finish of your porcelain fixtures. As gentle as they are, these compounds are still abrasive and will scratch your finish, especially with regular use.
In some cases where the tile surface has a texture that tends to get dirty easily, a penetrating sealer can be applied to the tile surface. The sealer acts as a bond breaker so dirt doesn't tend to cling to it.
Porcelain tiles tend to be harder, more resilient and more stain-resistant than ceramic tiles. They are one of the easiest types of tile to maintain but their surface can eventually be eroded by the regular use of corrosive chemicals such as ammonia, bleach or acids that can also damage the grout and loosen the tiles.
When it comes to cleaning stone, concrete, and ceramic tile floors, leave the vinegar under the sink. Just like with stone countertops, the acid in vinegar will strip away the protective sealant from stone tiles, making them look dull and leaving the surface vulnerable to etching and pitting.
The surface of porcelain and ceramic tile do not require sealing, however, it's important to note that even though your porcelain or ceramic tile does not need to be sealed, the grout used during installation will need to be sealed and maintained.
Grout that hasn't been sealed, needs to be resealed, or is in poor shape should not be cleaned with vinegar. The vinegar penetrates into the pores of the grout, further weakening the material. Over time, vinegar will deteriorate the condition of the grout by etching or wearing it away.
Rinsing is not necessary! If you're simply using a vinegar and water solution to wipe and disinfect, you won't need to rinse. However, if there's also plenty of dirt and grime you're wiping away, you may also want to rinse with some extra water.